Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Making The Tube Longer - DIY pump Extension ... Suggestions??

Making The Tube Longer - DIY pump Extension ... Suggestions??

I’m almost too long for the current pump I’m using (not because I’m long per se, I’m just long in the pump). But this pump is perfect and I cant find a replacement that has the same function with a longer tube.

So I’m wondering about a DIY manufactured/engineered extension to the pump.

Obviously someone good with melting and making plastics could probably just create a plastic ring and glue it on the end of the pump. But I’m not sure how I would do that.

Any tips or thoughts you guys have would be appreciated.

Looks like Cheeba may have done something ilke this, see his most recent pics to determine if this is what you were thinking.

cheeba - Cheeba water pumping progress


Initial: 7” BPEL; 6” NBPEL; 5.25” - 5.5” MEG

Current: 7.75” BPEL; 7.25” NBPEL; 8.5” BPFSL; 6.5” MEG; 6”x5” Flaccid.

Goal: Improved/consistent EQ while managing ED. Secondary: maintain current stats.

Originally Posted by 32quarters
Looks like Cheeba may have done something ilke this, see his most recent pics to determine if this is what you were thinking.

cheeba - Cheeba water pumping progress

Thanks for this

Unfortunately I spoke with the manufacturer and it appears that won’t work for my cylinder

Anyone with some engineering tips ??

Originally Posted by Don Logan
I used ABS pipe.

I cut off about two inches. Rounded the ends of the body side with #300 sandpaper. Smoothed the other end square. Caulked it to the end of the cylinder.

Caulk is a great idea. I was wondering whether super glue could do it but didn’t think it would seal. Did you just caulk around the outside edge? I’m concerned about getting it inside the tube

Originally Posted by BiggerPenis73
Caulk is a great idea. I was wondering whether super glue could do it but didn’t think it would seal. Did you just caulk around the outside edge? I’m concerned about getting it inside the tube


No, I caulked the two surfaces where they meet, not the outer area. And now that I think about it, it was plumber’s putty (a pliable, clay-like substance), not caulk. So, yes, it did squeeze into the inside of the tube. But I easily stripped it away with my finger.

I would not use super glue as I doubt it can provide an air-tight seal.


My Progress Thread | Ball Pump FAQs | IMAGE: Long flaccid | IMAGE: Ideal flaccid | IMAGE: Flaccid post-stretch | IMAGE: Big ballsack

"One definition of paranoia is suspecting the truth too early." - Walter Kirn


Last edited by Don Logan : 03-18-2022 at .

Originally Posted by Don Logan
No, I caulked the two surfaces where they meet, not the outer area. And now that I think about it, it was plumber’s putty (a pliable, clay-like substance), not caulk. So, yes, it did squeeze into the inside of the tube. But I easily stripped it away with my finger.

I would not use super glue as I doubt it can provide an air-tight seal.

Thanks for the tip

I bought a clear pipe piece and some epoxy

This is the result

Will try it for the first time tomorrow morning

IMG_20220321_225518569.jpg
(1.46 MB, 23 views)
IMG_20220321_225457319.jpg
(1.62 MB, 31 views)

Doing my session now. Works like a charm. My pump is now 9.5 inches long. As I’m barely at 8 fully pumped now, this extension should work for a while before I need to extend it again. Lol

Top
Similar Threads 
ThreadStarterForumRepliesLast Post
"Milking the Tube" Pumping with a flexible DIY Silicone basedickerschwanzPenis Pumps1511-09-2017 04:35 PM
Does a longer dong equal lasting longerluka4967Penis Enlargement1205-22-2005 04:35 AM
DIY: What to use as tube?sizemoorePenis Pumps912-01-2004 01:27 AM
Mityvac pump diy pumpiknowicanPenis Pumps711-01-2004 05:05 AM

All times are GMT. The time now is 08:58 PM.