Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Anyone have a X4 labs quad support extender that can give me some tips?

Anyone have a X4 labs quad support extender that can give me some tips?

I just got my x4 labs quad support deluxe edition extender in the mail. I am very excited to start using it. However I am a bit confused on some things about the device. For instance, do I use both comfort straps and both nooses all at the same time? Also where the fuck is the velcro strap its telling me about, i dont appear to have one? And how do I know what tension I am on? If anyone has this device and knows how to use this please help me with my questions and let me know if you wouldn’t mind me PMing you because I have a couple more questions, thanks.

Usually you would either use two straps or two nooses, but you could use a combination of the two. I use two comfort straps. The Velcro strap only comes with the top priced unit and you can’t buy it as an accessory. The tension spring the deluxe model comes with is 1500 grams. You have three 1/4 inch sections. When the first 1/4 is covered because the unit is compressed over it you are at 500 grams tension roughly. When the first and second 1/4 inch section is covered you are at about 1000 grams tension. When all three are covered completely you are at about 1500 grams tension. To put the Quad support on I just put two comfort pads on and slide the extender on with straps. Adjust the comfort pads directly under the straps. Make sure you do this because the skin pinch between the straps and the extender slots can be very painful! You want to be about 80% erect because that will give you a good head swell so it holds better. Fully compress the extender towards your body and strap in starting with the strap closest to the head. Check the straps for tightness a couple of times in the next few minutes. I wear it about 6 hours a day during the week, but never much more than an hour at a time. Take off the extender and let the blood flow for a few minutes before putting it back on. Make sure you clean with alcohol pads every few days to get the body oils off the straps and extender to prevent slippage. As the straps wear they tend to slip more, so you can either buy more straps or narrow the strap slots by putting a couple pieces of electrical tape in the slots. For the record I have gained about 5/8” with about 2000 hours of use in the 2 years. I hope this helps!

Originally Posted by Biff81
Usually you would either use two straps or two nooses, but you could use a combination of the two. I use two comfort straps. The Velcro strap only comes with the top priced unit and you can’t buy it as an accessory. The tension spring the deluxe model comes with is 1500 grams. You have three 1/4 inch sections. When the first 1/4 is covered because the unit is compressed over it you are at 500 grams tension roughly. When the first and second 1/4 inch section is covered you are at about 1000 grams tension. When all three are covered completely you are at about 1500 grams tension. To put the Quad support on I just put two comfort pads on and slide the extender on with straps. Adjust the comfort pads directly under the straps. Make sure you do this because the skin pinch between the straps and the extender slots can be very painful! You want to be about 80% erect because that will give you a good head swell so it holds better. Fully compress the extender towards your body and strap in starting with the strap closest to the head. Check the straps for tightness a couple of times in the next few minutes. I wear it about 6 hours a day during the week, but never much more than an hour at a time. Take off the extender and let the blood flow for a few minutes before putting it back on. Make sure you clean with alcohol pads every few days to get the body oils off the straps and extender to prevent slippage. As the straps wear they tend to slip more, so you can either buy more straps or narrow the strap slots by putting a couple pieces of electrical tape in the slots. For the record I have gained about 5/8” with about 2000 hours of use in the 2 years. I hope this helps!

Thanks for the response, but I dont understand how all 3 sections are the most tension. It appears that when all 3 sections are covered, the device is at its shortest length, so wouldn’t the longest length be the most tension? Also do I unscrew the area closest to the base to increase the length as my penis gets longer before I change rods to increase length, or should it always be screwed in all the way and the only way i should increase length is through changing rods?

Just push both ends of the extender together and you will see what I mean. The more you compress the springs the more push back you get. You turn both knobs counter clockwise to lengthen the extender. Once you continually have unscrew it about a half inch you might want to try and increase the extender length by changing rods. X4 has several how to video on Youtube that might make it easier figure it out. Good luck!

Originally Posted by ray32
Thanks for the response, but I don’t understand how all 3 sections are the most tension. It appears that when all 3 sections are covered, the device is at it’s shortest length, so wouldn’t the longest length be the most tension? Also do I unscrew the area closest to the base to increase the length as my penis gets longer before I change rods to increase length, or should it always be screwed in all the way and the only way I should increase length is through changing rods?

I use the x4labs. By having all three sections (lines on the bars) covered, means that you’re at max tension because the tension of your penis being stretched is causing the springs to be compacted down to the lowest point.

I wear mine by attaching the noose below the glans, and the comfort strap below that. In the beginning, I recommend going for the noose only. As you add greater tension, I find that the noose and comfort straps are necessary to keep it on for any length of time at max tension. The good thing about using the noose with the comfort harness is that the ends of the noose straps can be fastened in two places, giving it extra grip.

I’ve been posting my methods and PE journal on the x4labs forum. Look for Seeker’s PE Project and Keep the Ruler Handy by Seeker (me).

Good luck.


Start 10/24/10: BPEL: 6.0 BPFL: 4.25; EG: 4.75

Current: BPEL: 7.75 Base Girth: 5.75 UHG: 4.9375 NBPEL 6.75 Goal - 9.0 BPEL

(Extender to Bib Hanger|Jelq to Pump)

Top

All times are GMT. The time now is 02:30 AM.