CC widening

After reading many threads there seems to be some debate over where girth gains actually take place. I know firsthand that the CS is the first to expand because of the nature of that chamber. What I don’t have a firm grip on is the process of enlarging or widening (which is the best way for me to track the growth of the CC) the CC chambers. I’ve gained about 1/8 in diameter and it seems to be a little more than just improved erection in my opinion. Sometimes after a good clamp session I feel like my CC has expanded as the sides feel hard and pointed almost. I really want to see my penis get wider when looking at the top of it as opposed to just the side.

Some suggestions/threads I’ve read (that had no conclusion, abandoned, etc.) are:

Heat and clamping
Heat, clamping and bends
Jelqing while trying not to squeeze CS
Pumping

I’ve not seen a thread yet where vets say that they know for sure that they got wider from PE, only total girth measurements are given. Is this subject still an unknown or is there proof that this is happening and that there are particular practices to be efficient in growing in your CC chambers? I would love some firsthand stories of permanent gains and details on method/technique. I followed the thread and routine of tntjockey and it is great but would like the specifics of does it get significantly wider?

I can tell you from my 3 months clamping experience that the only place I’ve gained is in width but only in the area under the clamp.

The increase is really obvious viewed from above, the CS seems unchanged so far.

I see a lot of people say that they are gaining base girth from clamping. this leads me to the conclusion that the strain and pressure of the clamp is actually what is expanding the tissue more than the internal pressure created from clamping. I have yet to try it but I’ve often wondered if double clamping all along the shaft would actually be the key to faster gains.

I’ve always wondered if it’s actually the grip in jelqing that manipulates the inner chambers more than I has to do with the pressure being built up. In essence, erect stretching in a way.

I think I may carefully give a 6 week trial to test my theory and see what I come out with after that time. Hopefully all in 1 piece.

That is an excellent question.

At last, a use for the degree I’m taking :)

I thought about this in fluid mechanical terms and it makes sense. Although blood is near enough incompressible, applying force to it raises the pressure whilst keeping a constant volume and happens directly beneath the clamp. This is what I believe could be the cause of the base girth gains.

Now consider a balloon and a steel tank. A normal penis is flexible so acts like a balloon, when a fluid is pumped in it expands until the forces balance. Restricting blood flow (clamping etc.) increases the pressure hence greater expansion. However, if you were to clamp the entire shaft your penis would behave more like a steel tank, expanding a negligible amount, causing much higher pressures to be obtained than a single clamp.

It may also have benefits of reducing/removing fluid build up along the shaft. If you do try it be careful, I don’t want to hear about anyone’s penis exploding.

I’m thinking that the steel tank is a close analogy. However, I don’t think that I will initially approach it in that way. I’m thinking clamp at the base at 80-90% and then apply the other clamp enough to begin to get to 100%. Applying the second to a full on clamped erection is way to dangerous me thinks.

A closer analogy in my mind is more like a balloon animal type balloon. You blow it up to it’s full length capacity (not over filled) and then grab it in the middle anywhere and you get an indentation where the balloon grew from squeezing.

I have no degree but it makes sense in my little mind.

Xenolith tried something similar spacing clamps every half inch up the shaft, he claimed it worked well.

I tried it this morning and the pressure felt right. There was only enough time for one set for about 10 minutes. When I finished I took off the midshaft clamp first and had an indentation from where it was. It looked strange. I’ll try to get two sets in a row clamped at different places to see what happens.

Going back to regular clamping guys. This business is too risky IMO. Don’t want to get hurt and ruin what I’ve gained.