Just got my penimaster Pro. Need help with sluice size and comfort.

I just got my penimaster pro and when I tried to put it on with the already installed tan sluice (medium) I couldn’t get a good fit and would slide out. I only pumped the ball one full pump so I’m not sure if I should do an extra pump for more pressure?

I changed the sluice to the green one (the smallest one) and while it was difficult to get inside the chamber (I had to use the supplied lube inside the chamber and on the glans), I got inside and the one pump really pulled me in. I was able to attach the extender and after about 30 minutes it was getting to be a little painful. I let a little air into the chamber to alleviate the pressure and my glans came out slightly (or maybe it was a bit of the shaft as well) and it felt a little better but I still could not keep it on for much longer.

When I pulled out, the ridge on my glans (I’m circumcised) was very large and red and looked a bit inflamed. My penis looked like a bobble head! I’ve had it off for about an hour now and it still is a bit tender and hurts a little still. I’m worried if this continues I am going to damage the glans?

What is the best way to get a correct fit so that I don’t have the pain associated with it. Any guidance would be appreciated!

Had a little damage to my penis and had to take a break from the penimaster. Just tried the tan diaphragm and sluice and was able to get a firm connection and attach to the extending system without sliding out. Hoping this will be enough to alleviate the pain.

I’ve only had it on for about 30 minutes now and plan to check at the 1 hour mark. I’ll update later!

you dont need 2 pumps for pressure, one is enough

put lot lubricant inside the chamber and bit in your glans.

use minimal tension to start with,

you have to get a bit used to the slight pressure inside penimaster but if you feel much pressure, you probably are over 900 grams

Yeah, I have it at the first line when I have my penis pointing upward. When it is straight out, it is at the third line.

lowest pressure and disconnect after 30 min

you will keep getting more and more used to it and more expert

Just took it off. Got side tracked with the kids so it ended up being on for 1.5 hours. Never had any discomfort with it in. My glans is obviously swelled and looks a little purple and is a little sore but I think that will go away quickly.

The flaccid hang afterward is crazy! Wish it would be like that all the time!

Tips:

1) Wrap glans with micropore tape or similar glans friendly tapes to avoid blistering.

2) Squeeze the pump so that you have a little room to blow into the diaphragm before drawing the glans in. Make it bulge out of the sluice. This removes air that can be trapped between the sluice and diaphragm - which can cause blisters.

3) After the first pump, I personally squeeze the pump ball about 1/3 of the way and do a second pump do mount the glans fully. Sounds like you might need to do something similar. Experiment, but do so carefully and in a secure place where you can take the device off if something feels wrong.

Try to pull slightly on the chamber after you have mounted the chamber. Does it feel secure, and is the glans fully in? Or does it appears to slip? If it does, you need to experiment further until it stays in place.

4) It sounds like the sluice you are using might be too tight. I would continue to experiment with other sizes (yellow), and practise the mounting. Try to use as little vacuum as needed, but I too need a little more than one pump.

Some prefer the hose system for this reason. I personally could never get the hang of that and am now used to the pump ball system. You might have more luck than me with the hose system.

If the sluice is too small it will start to hurt below the glans easier than if the sluice is the right size (my experience).

One other thing:

Push into the chamber with the vacuum instead of just letting it pull you in. This will allow you to use the least amount of vacuum necessary.

Thanks for the tips!

For that tape, does it hurt to remove or leave adhesive behind? Looking at the 3m 1/2” microphone tape on amazon.

No problem!

The tape I use is a local brand and pharmacy that I can’t find online. It does work well for me and does not leave residue. No pain on removal. I see some of the 3M tapes are advertised as no residue and skin friendly. I’d recommend you try one of those.

I saw another remember recommending 3M nexcare waterproof tape. This might be worth a shot. I can’t seem to find the thread right now though. I will link it if I find it.

Edit: Here is the thread: link