Non Slip Mat ( NSM )

I picked up a roll of Non Slip Mat while out grocery shopping. It is 12 inches by 10 feet and costed less than $4. PE wasn’t my intended use at the time, but once I got it home I was curious.

So far it has worked better for holding on golf weights than anything I’ve tried. I got some hair ties, and tried them, but they slipped for me if I became active, but when I cut a strip of NSM ( a new acronym ) and rolled it up under the HTW; in front of the weights, they stayed on. I haven’t tried running with this set up, or sky diving, but it has held better than anything I have tried up till now.

The NSM is made of PVS/Polyester and claims to be easy to clean. I likely would have a life time supply if I limited it to PE.

Anyone else tried this stuff?

Is this the stuff? And what is your procedure for securing the golf weights with it? I couldn’t visualize your explanation.

Seems like shelf-liner.

Shelf liner! That’s a good idea!

One of the uses was shelf lining.

I’ve tried lots of stuff for non slip, and I am really liking this. It has all kinds of little holes in it, and each one helps grip it in place, and it allows for some breathing of the skin I would think.

Oh like that sticky stuff with the little bumps and holes. Not like adhesive sticky, like, like, I don’t know… innately sticky. I used to use that stuff to line the bottom of my pet snake’s terrarium and it is totally washable and kind of stretchy.

So how do you use it to anchor golf weights?

I wish I was better with posting pictures, but I will go the 1000 word route instead. Actually it’s really simple.

First I put on the hair tie (HTW) cut off just long enough to cover my dick , then I slide on the golf weights over the HTW. Then I roll back the HTW as far back as I can towards the weights. This exposes on the area just behind the glans ( probably about an inch or two depending how many weights, and how big your dick is ).
Then I roll a strip of the NSM around my dick until it is built up to make it keep the weights from slipping off. Then I just roll the HTW that I rolled back to cover the NSM, and let the weights down. I kind of make a ramp with the strip of NSM for the weights to rest on. When you are done, all you will likely see is the weights, and the HTW. Maybe a little bit on the NSM might be peaking out the end, but the NSM should pretty much be covered. Ramping down the strip (towards the weights) will keep it from unwinding, and the harder you pull on the weights, the tighter the NSM strip get as the weights go further up the ramp.

I will experiment a little more later today in a more active mode to see how well it holds, but yesterday with limited activity it held better than anything I’ve tried so far.

Something for rugs might be thicker and hard to wrap. I got it at Aldies Market.

I can’t find the actual stuff I got but I think this would be pretty much the same:

http://www.amaz … /dp/B006ZS16X6/

I just made a couple of posts which should answer your questions. I have to get going, and I’ll check back later.

There is nothing sticky, other than the material itself tends to grip. It is soft and full of small holes. It feels nice. I hated Coban (ow), but this goes on and off very nicely.

repeter, A keen idea. Thanks for sharing it.

The above description seems pretty clear. I gather the NSM is rolled directly onto your dick somewhere between the weights/HTW and the corona. How does your dick react to the NSM? No irritation and not painful to take off at the end of a session?

BTW I am into amateur woodworking and us woodworkers use NSM material under push sticks etc used to feed wood through a machine (eg sawbench)..

Repeter, yes, that description was excellent. The wrap goes behind the glans and the HTW rolls over it to hold the stack and keep it from unraveling. I despise coban tape, so I will try this.

When I said sticky I meant grippy. Like the way coban tape is grippy, but not as much. Not like an adhesive. I just couldn’t figure out the right words, thanks for your help. :)

Yep, that is what I am thinking of. I will try this out. I also like how it is thicker than coban tape so you wouldn’t have to wrap it ten million times.

from riding my bike and doing some outside work with the golf weights, and it is working great.

A person could experiment with different ways of wrapping, but I would think this would work with extenders, and heavy hangers as well.

My goal is to make the wrapping as simple and as effective as possible. To really make it hold, I think a person could run one layer of NSM all the way back under the HTW. This may be too tight for high girth people, I tried it last night, and it worked for me, and then I proceeded with winding a narrow strip of NSM under the glans. It was extra work, so today I just wound it under the glans with a half inch wide strip 12 inches long, and then a strip about 1.5 inches wide, and about 8 inches long. The 1.5 inch gave the ramping effect to push the golf weights against. This is what I am wearing now, and have been wearing for the last couple of active hours. I don’t know if I could pull it off without peeling back the HTW and unwinding the NSM. I’ll try pulling it off later when I want it off.

I would like weights to come off short of ripping my dick off, in case something caught on them. Normally I wouldn’t have wore golf weights bike riding if they wouldn’t come off fairly easy, but I wanted to experiment. If I can pull the weights off later without a lot of force, I will actually feel better about wearing the golf weights while doing my daily activities, but for now they haven’t budged a bit.

So far I like it way more than Coban. As a matter of fact, I tried Coban a couple of times and found it very painful to take off after being pressed into my dick for an hour or two. This stuff as you know is cheap, and very comfortable. It is made of PVC/Polyester, so seems like something they would make sweaters out of.

I originally got the NSM to keep my garden produce from freezing when in contact with ice. It works good for that. It also will keep guitars from sliding off from the amp when you lean your guitar against it (as long as no one is using the amp and vibrating it ), and it keeps soap from sliding off into the bathtub. Well anyhow, I’m not trying to sell the stuff.

I like the way Coban sticks to itself, but not the way it stuck to my dick. I could see using a little Coban over the NSM to hold it in place, but the HTW does a fine job of that.
I like the way we are all involved in this experiment. We experiment individually, and then share our results collectively, and when there are some individual gains, there is collective happiness.