Penimaster Pro Users...A Question

Hey all. I know this is an older thread.
I agree with the notion of taking breaks and going for as much time as you can get with tension - breaks are important. Especially to avoid injury to the glans - which as stated above will cause you to have to take a break.

Anyway, I’m having trouble getting into the damn PmP. Just got it and spent the last 3 hours trying to get in. The yellow latex was too small so switched to the blue. Lubed up and i get sucked in but slip right out. I’ve tried pumping a few times but its not tight enough. I’m going to try going back to the yellow and trying pumping a few times. Anyone have any suggestions? I invested a lot of money on this thing and it was only recently i experienced my first real gains with an extender as it was vacuum based (autoextender) so i chose to invest in one that had some data behind it. If i can get in the damn thing I’ll be fine .

I completely appreciate your frustration, the PMP is expensive!

Have you experimented with using the split adapter that comes with the set?

The split adapter will reduce the diameter of the chamber opening, as you might already know.

Also, what’s your process for creating vacuum and maintaining vacuum after insertion?

There is definitely a learning curve to the PMP.

Thank you for your response!

I have not experimented with the split adapter.

That may be my next move.

Right now - I’m putting my glans to the base of the unit (I actually guide it in quite a bit to be honest) while depressing the pump ball.

Once done - I take off the pump ball and my glans slips right out.

When i received the unit I received it with the yellow latex but switched to the blue as i couldn’t get my glans to go in. I think i may have to switch to the blue and force it in and perhaps that will prevent it from sliding out? The only reason this might work as it didn’t work before (otherwise i wouldn’t have switched out the bands to the blue) is to pump twice. I have pumped twice (I depress, remove the pump, squeeze then attach and depress again but this doesn’t work either) so perhaps this would work with the blue latex.

Haven’t tried anything else. I may have to try the split adapter if all else fails.

I don’t wanna start a new thread for just a question or two. If any experienced PMP users can help out; What is the difference between the Basic system and the Rod Expander system? Besides obviously $85.

Also any suggestions on what Accessories should be ordered along with the system would be appreciated.

Hey man.
I tried the yellow latex and pumping twice - even three times.
I was finally able to get the glans to get fully sucked in and it clicked. But the minute i put it in the extender it slipped out.

Is the split adapter the 2 rings that come in 4 different pieces?

If so, how do i use it?

Thanks.
Chris

I think the basic system just comes with the head unit. The rod expander system would obviously come with the actual extender.

I appreciate your input, and that is what I thought too initially. I don’t know that just seems strange to me. The basic system doesn’t actually offer the extender?

Their product IS the extender.

The basic system just comes with the head unit.

PeniMaster PRO - (basic system) Details

I’m curious if your using the stretcher with the blue head. Iv bought the medium and the small neither have enough suction to hold for a good stretch. My penis is not THAT small wondering if you have any tips?

They had an earlier product that was a noose based extender (which they now call there Penimaster Chrome, I think). I believe the point of the basic package is to use the vacuum chamber with your existing (older) Chrome extender. If you already had the old set, then you wouldn’t need a new rod extender, just the glans chamber.

I might be incorrect, but I’m fairly sure this is the reason.

It is and it isn’t.

The Penimaster Classic is the old system, it’s the extender with straps.

The Penimaster Pro is the vac based system, which can use the extender, weights, or a belt (ADS).

Brother I”m so fkg fed up with this thing I can’t use it.
So you mean the actual head of the unit is blue? Or are you referring to the sluice or latex? If your referring to the head - mine is white - just like in the marketing photos.

I never ever have issues with suction. I never slip out.

I think you need to watch the video on how to apply the two pieces of latex so it is correct. You may also have a pinhole in your latex which is what I suspect.

What video are you referring to?
The one on the website?

Do you experience any swelling around the glans, that’s the problem I have? Is there anything you do to prevent that? Thanks