Pro Extender 3

Hello guys! I started this thread about the proextender because i have a doubt of what it is the minimium of tension in the extender , I know it starts with the mark of 900 but before the mark there is a little space , I would like to know specifically wich tension is, does anyone know that??

According to the pamphlet the 3 markings are for 900, 1200 and 1500 gr. 900 gr being the 3rd marking. I’ve never been able to stay on 1500gr, most of the time I’ve been using it somewhere between 900 and 1200gr.

How did you get to those lines ? ( i mean 1200 and 1500) what I do is doing force of a couple of seconds through my penis base with the device stucking it for a couple of seconds in the mark that I want and then I let it go and I can see the marks , is it that the correct way or you have to not to look the mark you are selecting , i concluded that what I do is the correct thing and also there is no method to do the traction and ocult the marks , tell me what do you think! And also , have you got any results yet??

You’ll never get to the last line (the 1500gr mark), check for yourself, compress the extender using just your hands and you’ll see.

To stay inside the 900 and 1200gr marks:

-make sure your extender’s size is fit for your dick, I.e. If your dick is 18cm long BPFSL, sustract your head (I.e. 2cm + 1cm more) = 15cm is the place on the shaft where the noose must rest, then you should set your extender just a little bit over 16cm (when compressed it should match closely 15cm, because it compress for 1 cm)

-make sure your noose is not loose on the down side of the sledge (you should have two slots or places to fold the silicone noose below the head piece), tighten it using velcro or some adhesive tape so it stays in place and won’t slip. Use talcum if needed.

-the noose should be about 1cm behind your glans, on the shaft, your head should be placed well in front of the sledge when compressed, your coronal ridge almost over the two holes where the noose goes through, that way the noose is almost perpendicular to your penis when pulled and secured in place.

-doing so, the pull forces should feel on your shaft mostly and not just in your head, and should NOT be making the “hangman” on your penis, like trying to pull your head off. Then adjust the screws to add just a little more tension if needed. That should put you on at least over 900gr line.

I’ve been using it for over 1 year, and went from 17cm BPFSL to 19.6cm, and 16cm BPEL to 18.3cm. It works, but its slow as hell, so be patient.

Bfn.

Has anyone got good results of the pro extender? And also , how was the experience and the time it took . Before alll , thank you all very much

Why dont you use an ultrasound unit or HEAT? It will aid with growing your BPFSL faster than using the creep methods. (stretching your penis)

Sory , what is the ultrasound unit or the heat?? I didn’t know them

I have the imitation one from ebay, I find it discomfort an sometimes painful , not used long enough to know if its working yet.

6cm grown thanks to this device, actually I had the proextender 2, and the 1. Never tried the 3. However, it’s taken me around 5000 hours to reach this growth. Started in 2012 and this year it’s 10 years. Took some years off, always tried to reach at least 8 hours a day when doing it constantly. No rest days. Had many issues with slipping and tried many solutions. Finally at the end of last year I discovered doing soft clamping for 15 minutes made my glans bigger so the noose wouldn’t slip that much anymore and I now can use it at max tension for 6 hours a day and the rest at lower tension.

I did an experiment on 24/7 stretching (or closest possible to that) and was able to do 16 hours stretch with extender and slept with sheath on which I placed in at erect state so it stays all night elongated, on a sheath that was not tight nor loose so the circulation is not compromised. Had done it for a week or so plus continued with high tension stretch ever since. It kinda made the trick. I;’ve grown at least 1,5cm since february 10th.

My flaccid has grown around 3cm since October last year, although I’m a grower so I’m becoming a shower. Am now at around 21cm long BPEL. Started somewhere around 15cm. +/- 0,5cm.