BH suggestion/feedback

Bib, I will post answers to all of your feedback questions as soon as I have a little more time logged. Actually, I am not keeping a log of the time and probably should. I have around 10 hours or so since getting my BHS (Bib Hanger Starter)

Anyway, as everyone says, there is a definite learning curve. I would have benefited from some diagrams on for both proper wrapping and the proper location for attaching.

My first mistake was attaching the hanger like I do with my hand for manual streching ie: thumb on bottom and forefinger on top. BIG mistake. I may be the only idiot that did this but it took me 2 days to realize my mistake.

The second thing (actually was the first) was not using enough “sweatshirt” material. I used only enough for once around and that didn’t allow me to get the theraband snug.

Also, I am still uncertain about the proper hanger position when hanging. This subject has been brought up many times and many times you have answered. I attach the hanger about .5” to .75” from the glans with about .25” of wrap from the front edge of the BH. Almost immediately after adding weight the BH pulls the wrap in contact with the glans and the BH is supported between the glans and the wrap.

Again, diagrams would be VERY helpful to me. I will make a couple rough drawings and attach them here so you can see what I mean.

Don’t get me wrong, you have done more than enough to help all the PE community. I am just responding to your request for feedback.

Thanks, NE

diagram of beginning the wrap

diagram of completed wrap

diagram of attached BH before weight

diagram of attached BH with weight

NotEnough,

I have not seen the diagrams yet. They have not been released and damned if I know how to do it. I promise to learn. Anyway, I have to leave in a minute and wanted to respond to the written part.

>I would have benefited from some diagrams on for both proper wrapping and the proper location for attaching. <

I have worked on some diagrams, but so far, they suck. Will continue to try.

>Also, I am still uncertain about the proper hanger position when hanging. This subject has been brought up many times and many times you have answered. I attach the hanger about .5” to .75” from the glans with about .25” of wrap from the front edge of the BH. <

Wrap starting at least .75 inch from the glans and put the hanger .25 behind the start of the wrap. Or if you put the hanger on the edge of the front of the wrap, then start the wrap one inch behind the glans.

>Almost immediately after adding weight the BH pulls the wrap in contact with the glans and the BH is supported between the glans and the wrap. <

No, see the wrap must be started far enough back so the skin folds on itself and goes over the glans to protect it. If one inch back is not enough, then put it further back. If you don’t understand this, please say so and I will try again. Very important, neither the hanger or wrap should ever come in contact with the naked glans. Skin should always cover it.

>Don’t get me wrong, you have done more than enough to help all the PE community. I am just responding to your request for feedback. <

No problem. Some guys need more help than others. Never be afraid to ask questions.

Bigger

NE,

Ok, back again, and all of that looks fine, except you are starting the wrap way too close to the head. I assume from the drawings that you are cut. A good rule of thumb is to start the wrap with the forward edge on, or slightly behind the circ scar. This should assure plenty of skin to fold over and protect the glans.

But whatever, have the hanger no closer than one inch behind the glans. It can be further, but that may stretch excess skin.

Any questions, just ask.

Bigger

Well, I guess I have been doing it wrong “again”. I will try your suggestion.

To clarify, should the skin stretch and allow the BH to slide into the same location I show in the diagram but with skin between the glans and wrap?

Thanks, I will continue to report. I can’t believe I am the “only” one with a slow learning curve (haha)

NotEnough,

>To clarify, should the skin stretch and allow the BH to slide into the same location I show in the diagram but with skin between the glans and wrap?<

Yes, under heavy weight it will slide some. Under ten pounds, it may stay at about the same point.

>Thanks, I will continue to report. I can’t believe I am the “only” one with a slow learning curve (haha) <

You are not the only one by any means. Some people think differently and understand different things.

I am going to continue working on drawings to put on my sight. It has only been a few months. heh. Maybe that will clear everything up for all. I will try to post them here.

Bigger

Well, I tried your suggestion and it was “better” (more comfortable) but the hanger still slid down some at 7.5 pounds. Ended up with the skin bunched up about .25” wide between the BH and the glans. I will continue to experiment with tightness. I will also need to stretch the skin some more.

NotEnough,

>Ended up with the skin bunched up about .25” wide between the BH and the glans. <

As long as it stays off the head, and allows circulation, it is ok.

Bigger