Length gains from pumping?

Hi, can I ask a few pump questions?

I bought a pump a few years ago, but sadly I realised that it was to short. I have now made me a new cylinder and are planning to start up again. I have found that my pumped length inside the tube is quite longer than my my NBPEL, even my BPEL, on the other hand I have always had problems maintaining a proper erection for measuring. I use short sets, 5min or so, and then jelq a few minutes.

My question is: How does pumped EL correlate to the other measurements?

The pump does not have a gauge, and I’m concerned with how much pressure I should use. I usually pump until I feel a weak stretch in my CC’s. Is that okay or should I reduce the pressure?

I sometimes see that my unit gets a little blue, but that goes away when I jelq, is this maybe a sign that I am using to much pressure?

My final question is:

I have noticed that when I tilt the tube down when I pump it stretches the ligs, could this be a good way to go for length?

Hope someone can help a humble Norse

giveme9,

My pumped EL is the longest of all my measurements and that’s how it should be. After all, it’s a bone pressed measurement while your cock is being vacuum stretched.

If you are going to become a serious pumper, you should save your money and invest in a professional system with a gauge. It is the only way to know exactly what you are doing and it is a much safer way to pump. I would recommend the deluxe system from lapdist.

Blue means too much pressure or too much pressure and time, or even pumping up too fast. Try to avoid it. The best way to progress in pumping is not to always increase pressure, but to increase time.

If tilting the tube down seems to be a good technique for you, then do it. A lot of PE is in the power of positive thinking, and if you think the tilt is good, well, then it is.

Gprent,

Thanks for your reply, I’ll try to get a gauge on my pump.

I have been thinking of a new approach to the hole condom pumping idea. If you take the micro-tear idea and couple it with normal sport injuries, then it seems like the best way to treat these injuries is to follow the R.I.C.E Principe (Relax,Ice,Compress,Elevate). That may be the reason why condom-pumping seems to work so well. That the compress stops the inflammation process due to the micro-tears. I was thinking what if you also cooled down the penis at the end of your session. Then you would get the a double effect. Both stopping the inflammation process and also conserving the stretch produced by the pumping. Icing down while stretching is a well known treatment to increase flexibility in ligament in other parts of your body. Maybe this could be a good way to go for length gains with pumping. I think I’ll give it a try.

If it sounds crazy please comment.

A inner tube cock ring is a cock ring I made out of a inner tube from a 27 inch ten speed bicycle, just big enough to put one finger in and I have two half inch pieces but you can add more pieces to make a tighter fit around your penis.

I usually Take about a two minute break between sets and jelq for those two minutes and then reapply the cock ring and start pumping again.

I only lost about 3/16 of an inch after stopping three days but don’t know if the lost of inches would keep going down after the three days.

I think if you gain about 3 or 4 inches off of pumping or any other PE exercise I do not think it will ever go back to your original length.

OH yea I just recently started jelqing after each set so don’t know it it has been helping any.

Quote:
Originally Posted by EJ
Gprent,

What is the disadvantage of a tapered cylinder (a la Kaplan pump)?

Do you have a tapered cock? Mine is pretty much constant girth and a lot of guys head size is larger than the shaft. The geometry of a tapered cylinder is just wrong.

Actually, I do. 6” at the base narrowing to 5.25” right below the head. I really don’t want my base girth getting any bigger, but I’d like the rest to catch up so my dick is more cylindrical.

Well OK then. Buy a 2” diameter cylinder from lapdist.

Thanks for the info, Nelson.
I live in a country where I cannot but cockrings from anywhere, so please tell me how you did it from the inner tube.

Cut the inner tube in half and then cut out pieces that is about half an inch to one inch wide and then all you have to do is stretch them around your penis. And put them at the base of your penis.

That is pretty much it.

I maybe able to scan one and post it if you like so you can see how it looks

Yea the scan sounds very useful, I’ve been having trouble understanding what it is exactly,

But I assume it’s very similar to a cock ring or is a cock ring, just a little confused:)

OK should be ready as soon as a moderator approves the pictures

Yea but the inner tube cock ring is made of rubber and doesn’t erode when exposed to oil.

OK the inner tube cock ring is smaller in size than the pictures show.

They are just big enough to put one finger in.

All you do is stretch them over you penis and put them at the base of your penis.

You can add more pieces to apply more force on the penis but do not add so many pieces that you can not get a good seal on your pump.

If those rings are so small you can only fit one finger in are they a bit tight for a pumping newbie?

Would you suggest trying something a bit larger or would it be ok, just seems like it will be a lot of stress on my unit

No they stretch pretty easily and you can just start out with on ring instead of two, and add more rings as you get used to pumping.

Just remember if you do not want that much tension just cut the pieces smaller in size. About 1/4 to 1/2 inch instead of 1/2 to 1 inch.

Cool stuff Nelson! I’m going to try this for sure!

.Running to wal mart to get an inner tube.