Pipedream max precision power pump

Does anyone have any experience with this pump? I just got mine in and tested it on a half erect member and must say the sleeve feels very tight. And that is at an erect girth of only 4.5 inches.

For reference, the tube has a circumference of 6 inches. Does the sleeve look to tight?

Also, what is the black pin next to the pressure gauge? I really couldn’t find out myself and it came without proper description of the parts.

Image has URLs on it, not allowed in the forum.

I’ve had one of this pump and it lasted for 2 years. Considering that I paid close to nothing for it, it went the distance.

I remember messing with that pin next to the gauge. I didn’t figure it out what is for.

I am sorry and thank you for your help once again. You had the Max Precision pump as well? How do you feel about the sleeve? It feels way to tight IMO or is it normal to feel like a strong clamp? I am sorry, it is my first pump and I can’t come across answers via Google.

I figured out the pin is where air extracted from the cylinder leaves the pump.

About the gauge though, is it normal that with the first few pumps it doesn’t report any pressure?

I had just the pump. Back then the cylinder was Leluv and bought the pump and cylinder from different places.

Before my registration here I’ve pumped with the sleeve but it’s way too uncomfortable.

It’s normal to not read any pressure on the gauge, on the first pump or 2. It depends on your erection level and how far you press the pump lever.

So you just discarded the cylinder for another one? Sorry, I am very new to this but if you put another cylinder on it, will the gauge still be accurate?

Also, what did you find uncomfortable about the sleeve? Too tight, too little stretch? Weird opening? Should the sleeve mimick the effect of a penis ring or is the purpose just to prevent air from coming in?

I bought them separately: the pump from seller #1 and cylinder from seller #2. The pump had a male hose connector and the cylinder a female connector.

I felt too tight with the sleeve.

I think the pump sleeves were made to clamp the veins in order to keep the erection, since the pump was conceived in order to aid people with ED. This way, once the person release the pressure, the erection won’t fade.

The gauge could be evacuating a jelly jar and it would be accurate. The type of container being evacuated has nothing to do with what pressure the gauge sees.

You just can’t connect a leluv cylinder to this pump without converting the pump hose line with a male quick disconnect fitting that will click into the female quick disconnect on the leluv cylinder.

This set-up is good enough to see if you are going to like pumping enough to buy a better system when this one craps out.

Alright. Just for reference, you did get the pump from the Pipedream Worx Max Precision pump? Sorry, it has not explicitly been stated and I want to make sure, just so I can hear your review on it (there aren’t any online). Also, would you think it is okay for me to cut the sleeve so that it’s opening is wider? I already tried pumping without a sleeve but with the high tube diameter this is pretty hard (or I just haven’t mastered it yet).

I am sorry if I sound like a nitwit to you, I have been through years of misery from an injury caused by improper PE and am finally feeling good about it again.

It wasn’t from that brand but identical in appearance. I think there’s an picture of it in my thread.

Search for a right size cylinder and pump without the sleeve, that’s what I would do.

Alright. One more question, how tight should I screw the gauge on the pump? As tight as possible I assume?

Mine was cemented shut. Be gentle with it, plastic doesn’t like tight screws.

The gauge should already be properly torqued and sealed when you received it new.

Did you remove it for some reason? If so, you will probably break it if you tighten it as much as possible. Much better to put teflon tape on the threads and give it just enough torque so that it feels tight and lines up nicely with the barrel of the pump. Do not over tighten!

@Gprent I did screw it as tight as possible but I believe not to the point where I damaged anything. I can still screw it looser after all.

Also, how high are the odds my gauge isn’t functioning properly? After causing some discomfort from the overly tight sleeve I decided to take some time off. Today was my first time pumping again and decided to try sleeveless. I was definitely able to achieve a vacuum and even ejaculated in the pump, however the gauge did not perceive any vacuum. Afterwards, I tried it on my chest and went up to 2hg and found if I went any higher it would become painful. Now, this might be because of the different type of surface but still.

I think it might be time to invest in a more professional set up. Take a look at this starter kit from thickwall:

https://thickwa ll.co.uk/shop/p … s/starter-kits/

Can you propose other high quality pumps? The one you propose can’t be shipped to a parcel point which is a requisite for me since I don’t want to gain suspicions from my family.