Cylinder size for curved penis

Hi everyone,

My unit has an upwards curve, like a banana when erect. I once bought one of those cheap pumps which had a cylinder larger than my base and it never sealed properly or my testicles were drawn into the cylinder by the vacuum. But because of the curve, my penis was still pressing against the opposite wall of the cylinder when erect . Now I’m considering buying a better pump with a custom cylinder for my size, but how do I choose the size? I’m concerned that if I just buy the correct size, my unit will get stuck inside without fully expanding when erect. Has anyone had such a curve issue and still managed to use a custom-sized pump? Thanks in advance.

The following is a good sizing chart:

Cylinder sizing

Girth ——-> Cylinder Diameter
3.50 to 4.50* —> 1.50
4.75 to 5.25* —> 1.75
5.50 to 6.00* —> 2.00
6.25 to 6.75* —> 2.25
7.00 to 7.50* —> 2.50
7.75 to 8.25* —> 2.75

Unless you have a sever curve (0ver 20%) the above should provide you with the proper size. Just make sure you use plenty of lube prior to entering the cylinder.

This is base girth right?

Maximum shaft girth, including glans size.

Gotcha, thanks!

Thanks!

Looking at the chart, I bought a 2.00-inch cylinder as the girth at the base is almost 6 inches, however, in the middle section, it is only around 5~5.25 inches.

It seals well, no ball-sucking problem . The base section is packed for around 2-3 inches. So due to the interesting shape of my unit, when I pump around 5 hg, the bottom part of the tube is all filled however there is lots of space around the middle of the shaft and up. So it looks kind of weird when pumped, the girth difference becomes more accentuated as the bottom part fills the cylinder completely but the middle section seems to enlarge a little bit.

So now I’m wondering, should I have bought a 1.75 sized cylinder? But this time I would have problems fitting the base in it?

Can I expect the middle part to fill in and even out by time?

You have the perfect size cylinder. As you gain more experience and increase your continuous time in the tube up to 25 to 30 minutes, your entire shaft will start to expand. Take your time getting there and keep the pressure no higher than 5inhg.

This ^

Thanks!

In my case, when I’m fully up, my head and mid shaft is about 1.7-1.8 inches across
And the base is near 6. 5 5/8 maybe

I’m looking to plump the whole thing up and not keep some from expanding while some does;

I want uniform growth to keep the same general wide shape, and just make it bigger.

I’ve been reading around but I’m still unsure why the charts are sized that way (aimed for length and girth gains rather than girth ?

I don’t know if my big/wide head will park itself smack on the acrylic and be uncomfortable ; giving donuts, fluid, malformation etc.

I was thinking 2.25” seems logical, for gaining girth; and then length

If it’s backwards and retards length ? Idk, I was hopeful to stretch a bit and get a tension device; and also clamp when I am comfortable with the helaing, building, regiment I find, follow, etc

I have found the size charts but I have been unable to find the original developed reasons why people like tilest recommend it and not what I’m asking. I’m having a difficult time understanding is all.
I had been hoping to go with an elliptical that was wide but then I was looking at boston pumps contoured ones; thinking maybe 10 inch (7.24 BPEL I think, and ~5.5”mid shaft girth, over that at base.

I want to overall fatten my shaft uniformly so I’m at least 5.5” average across the 5” areas when it isn’t fully hard. ; I’m looking to reach 5.7-5.9” girth at the 5.5” places, permanently and maybe get to around 8.5ish length, just to get a little better knock around;
I want to make it thick and I am partly aware of what works, I’m really trying to match probably tilest but maybe not to go for as much length

Now…… if I got to his girth, or even 6.2-6.7” and only 6.7-7.0” nbel (non pressed was not a typo) then idk if the length gain is significantly more difficult and hence why tilest would recommend the tubes the tolerance they do. See idk though because everyone is not going to do the same tek but I don’t want to set myself back by getting a 2.25” contour or wide-flange and have problems (that aren’t ball or skin suck, because I was figuring for that). The 1.75” on the elliptical from LApump was I believe a good option for me but still I wasn’t sure at 1 3/4″ – 1 7/8″ which is 1.75” tall by 1.875” wide because I think I would pack the tube across immediately and I don’t want to get stuck or hurt or something

Please help guys, I searched alot and I am not finding it. I know I missed it but I think I need some help

In brief, the head is a mushroom tip wide at ~1.8”
Midshaft is ~5.5” and ~1.7” wide
Base is at least 5 5/8 around I think, but there’s some lower than 5.5” and when I’m not rock hard it’s more like 5”; so this is something I’ll love to improve I hope.

There are 2.125” is that something I should do ? The big head is maybe a problem or not idk ¯\_(ツ)_/¯

Thanks

Please let me know wha