The big penis and mens' sexual health source, increasing penis size around the world.
Ok so I busted out the callipers…
Base width (half an inch from pubic bone) = 1.45 inches
Mid width = 1.5 inches
Top width (just below glans) = 1.61 inches
For the record, my girth is between 4.4-4.7 inches depending on where its measured. A pretty skinny penis :(
2” wide, 5.5” mid-shaft EG, 6” base EG
If girth is king, why the hell does everyone keep talking about length?
1.5 inches mid shaft.
4Foreskin ;)
Just hair over 2 inches…6 inches in girth.
Are obviously these measurement taken with a rigid ruler, but the definite measure should need a caliber!
:lisa:
HI GUYS 1 3/4 across 51/4 around, cut , shaved LOL
Are obviously these measurement taken with a rigid ruler, but the definite measure should need a caliber!
:Lisa:
Yeah, a rigid ruler here.
Not particularly accurate.
Starting stats:- Dec11th2008 7.2"bpelx6" meg.Mar23rd09 8.375"bpel x 6.125"meg. Mar10 8.4" bpelx6.125" meg.
Goal: 8"nbpel x 7" A one eyed monster by any standard :)
It’s accurate if you line up your shaft perpendicularly with the ruler on both sides(with one eye of course).
Decemeber 2007: 5.8" BPEL x 4.9" MSEG
Current:-------->7.7" BPEL x 5.7" MSEG (7.2" NBPEL)
Current Goal:--->7.6" BPEL X 5.8" MSEG Do or do not, there is no "try".
Ok so I busted out the callipers…
I started to try this, but that sharp metal was too scary. Would get a nice acurate measurement though.
Current average: NBPEL 7(ish)" / MSEG: 5.25"
ST Goal : NBPEL: 7" / MSEG: 5.5"
LT Goal: NBPEL: 7.25" / MSEG: 6"
I think it would be better to use two eyes actually, since if you move your head you’ll probably move your hands.
I think it would be better to use two eyes actually, since if you move your head you’ll probably move your hands.
Yeah that’s the tricky part. But I use two hands to keep it as still as I possibly can when I move my head.
Decemeber 2007: 5.8" BPEL x 4.9" MSEG
Current:-------->7.7" BPEL x 5.7" MSEG (7.2" NBPEL)
Current Goal:--->7.6" BPEL X 5.8" MSEG Do or do not, there is no "try".
For the record, I measured a perfect cylinder that has a girth of 6.375.
It measures a tiny bit over 2 ” in all directions (Obviously, because it’s a cylinder).
Just thought I’d share that. I don’t know if that helps anyone’s research.
I’m 6.5 inches across with a girth of 13 inches. That’s right, a shovel head!
Just thought I’d share that. I don’t know if that helps anyone’s research.
I’m 6.5 inches across with a girth of 13 inches. That’s right, a shovel head!
:funpost: Man you’re on a roll.
Decemeber 2007: 5.8" BPEL x 4.9" MSEG
Current:-------->7.7" BPEL x 5.7" MSEG (7.2" NBPEL)
Current Goal:--->7.6" BPEL X 5.8" MSEG Do or do not, there is no "try".
I always thought that I was pretty wide at 2 inches, but from what everyone is posting here I guess not.
HI GUYS , Kinda hard to get a good reading , I figured the best way was to use a hole template that you use for drawing with , then you know exactly what size if it fits in HOLE