Ran into a slight PenisMaster problem...

Well, I’ve had my PM for 2 weeks now and so far I love it. I’ve managed to log in at LEAST 5-6 hours a day every day thus far.

My goal was to start slow as far as tension goes and work my up bit by bit. I never had a problem really with circulation or the noose slipping off etc. so all was well.

So today I decided to add 2 small rods for more tension and I must say that I’m having a hell of a time keeping the damn thing on. In order to do so I need to really fasten the noose tight, which unfortunately causes inevitable circulation problems.

I’m hoping this is a temporary set back and that I just need a few days to adjust, but if it continues, I may need to go back down in tension a good deal and go alot slower than I thought.

Anyone else with similar problems?

You could make your own custom sized rods by cutting a threaded rod (about 1$ for 3 ft) to the desired length.

Take some Johnson’s & Johnson’s Hurt Free Tape, tear off about 10 inches, wrap the shaft behind the gland and back toward the head. This will help keep the head from slipping through the noose. Another thing you can do is take a piece of two-sided velcro strap and wrap it around the entire plastic housing through which the straps proceed. What I do is take after everything is installed, pull the end up the strap around and up so that the ends are wrapped around the sides back toward the top. Then I take the velcro and wrap it around and pin the strap ends to the PM. This will keep the straps from slipping.

When you up the tension is will cut down on the amount of time you can wear the PM. About 30 minutes is a rule of thumb with max tension.

Cool. Thanks.

Piet

The problem is not the length of the pipe, it’s the noose device that holds your boy in place. At a good deal of tension it is VERY difficult to keep the head of your penis from eventually slipping out.

OMG!!! Only 30 minutes? I used to wear mine for at least 8 hours a day while I was out of the house and wouldn’t take it off until I got home. I really wish I would have known about this site back then.

i was thinking of buying one of those. how well do they work. i was wondering how you kept the head of your willy form popping out of there?

……exactly as described by marty above. Velcro works well, as does an elastic band of the right size. I use a velcro cable tie which can be found in any DIY store in the UK. I’m using the strap type fastener rather than the loop, although one strap has already snapped after only 2 months. I’m thinking of replacing the rubber strap with a velcro band over wrapping - should be as/more secure and faster to put on/take off.

Before buying I would look into making your own - some excellent designs with instructions at this site, just search.

Mellors

I have been wearing my Penimaster for a few days now and averaging 5 hours per day. The first set I can usually go for 2 hours before having to take it off due to discomfort. But after that I can only wear it for 30 minutes at a time before I have to take it off.

What happens in my glans get squashed up as they try to pull through the strap. With 4 notches either side it is too loose, 5 on one side and 4 on the other is OK but if I pull 5 through on each side it cuts off circulation and it feels like I have pins and needles on my Glans.

Because of this I would not dare to wear it outside. I only use it indoors where I can check everything is OK ever 15 minutes.

I have been using the black sock that came with it, have you?

Thank you all for the suggestions. It is most appreciated. I’m off to buy some J&J No Hurt Tape! :)

Marty, Mellors, & leather:

In follow on to your suggestion about velcro here is a concept for a replacement strap for the penimaster that I have used now for about a month that has solved slippage and discomfort problems for me:

Trying to Make it Better

Best Regards,

MrTiPS

In follow on to your suggestion about velcro here is a concept for a replacement strap for the penimaster that I have used now for about a month that has solved slippage and discomfort problems for me:
[MrTiPS
[/QUOTE]

Thanks for living up to your name! I’d patent that PDQ if I were you before Penimaster steal it………

Just a thought: my olympic barbells have collars (made by steelflex) which contain a cylindrical sheath inside which reduces in diameter as you tighten a screw on the outside. This gives an even application of force on the bar. A series of these in different lengths would be good as an all day stretch device, just haven’t figured out a way to do it yet. However, I plant the seed in your minds where it will wither …… but may find a fertile ground somewhere.

Mellors

Whats a penismaster?

Are you still doing this and what gains have or did you make from wearing the Penimaster?

Marty5379

The J&J Tape is working great!! Thanks for the tip.