Wild tunica stretch.

I have had excellent early success with a home-made stretcher, but recently I have seen my length gains stagnate.

In the first six months I gained a full inch in length with the stretcher, probably a mixture of ligament pulling and some tunica elongation, and I`m ecstatic about the new inch, but I`ve hit a plateau and in the last few months I`ve remained at 6 7/8” erect bone-pressed length.

This morning the idea hit me that I could clamp both the top and base of my penis and focus the stretch only on the shaft, leaving the ligs unloaded.

I managed to stretch the tunica just over an inch for half an hour without any load on the ligaments whatsoever.

I will try this five days on and two off for half an hour at a time while sitting in a hot bath, after which I will measure my erect length again.

Be careful!

Good luck, keep us posted.

What kind of stretcher do you use?

The stretcher is one I copied from a picture I found here and made from parts found at home depot.

I find that the new two clamp stretch is less taxing on my dick and even though I did the stretch twice yesterday there are no bruises from the clamps as there always are from the single clamp stretch.and I woke with 100% EQ into the bargain!

Can we get a picture of this stretcher? Maybe even some instructions? :D

I`m unsure as to how to post pics, any ideas?

If it is a draw, just save it as a jpeg and upload here - post reply button, then in the new window at the bottom ‘manage attachments’ button.

If it is a pic of your penis, than you should ask to a mod that this thread is moved in the ‘member pics’ section.

The idea isn’t new, it is basically the ‘two way stretch’ concept.

In the pic (sorry for the quality) there are two clamps, one at each end, separated by barrel expanders used for tightening wires or rope.

With the device clamped at both ends of the penis, the barrels can be turned to increase the distance between the clamps, and in so doing, stretching the penis.

I use this device in a hot bath, increasing the stretch incrementally over the space of half an hour or so.

I have used a single clamp device for 9 months now, and just switched to the two clamp yesterday.

It is critical that you wrap your penis with some sort of material before clamping as the clamps will not hold properly otherwise and will cut your skin as well.

The material I use is a rubber sheet used for opening jars or making non-slip surfaces.

The material looks like it is woven, but is in actual fact molded that way, and provides 100% grip for many applications.

I use it for a grip for my weight bars when deadlifting and bench press to stop my hands slipping.

It takes a while for the right fit to be established and the clamps will slip occasionally if they aren`t on tight enough and will frustrate the hell out of you.so experimentation is the key initially.and do not leave the clamps on for more than half an hour, otherwise you run the risk of tissue damage that could be permanent.

This type of stretching is pretty radical and when I first posted my methods, some were very critical, suggesting that I ran the risk of injury.which, if done improperly is quite true.

So, here`s the caveats:

Watch for all the typical physical indicators; loss of EQ, bruising, unreasonable pain and discomfort ( you should be able to use your dick as normal afterwards.urination, sex, masturbation.directing traffic )

Given that you are sensitive to the above, you should find that the stretcher, either with the single clamp (which I used for 9 months) or with the double clamp.once you feel your ligs are pulled out entirely.gives you hours of good positive stretching focused on that pesky tunica that stands in our way.

Alrighty, it’s much more clear to me now thanks to that picture.

But, what kind of clamps are you using for both ends?

The clamps are threaded you-clamps with a flat plate across the top pressed down with the bolts that came with the you-clamp.

I use a 1 1/2” you-clamp at the top and 1” at the base because the clamp has to be used flaccid.

Getting an erection while in that device would mean some frantic un-bolting!

Actually, with the two clamp device attached, it is physically impossible top get blood into the penis as the clamp is on too tight for blood flow.which is why you MUST ONLY wear the device for a half hour at a time with ample time between sessions for full recovery.

I have only ever done two sessions with the stretcher in a day, which was the first day I tried the two clamp version, as I was so excited to finally be able to directly stretch the tunica, and I found little or no duress to the skin of my dick or any negative EQ.

The single clamp version, while really pulling the ligs nicely, seems to be harder on the skin of my dick, leaving bruises and discolouration along the shaft which my wife noticed on several occasions.

I put the bruising down to marks from riding my bike 30-40 km, and I hate to lie to the girl, but she wouldn`t understand PE!

And who cares that the idea isn`t new, and it isn`t a concept, it`s working device that provides benefit to those wishing to stretch their dick effectively and efficiently.

I`ve gained an entire inch using the device for nine months, and this week adapted the device to directly stretch the tunica.which I believe stands to be the #1 barrier to most gaining past the newbie phase of their PE career.and so hopefully this will be of great assistance to those wanting to use a safe, effective long-term way to inches.

And I realise that English may not be your native tongue Marinara, so please accept my correction in the way it was intended.to help us all here get bigger dicks.

That`s why we`re here, right?

A-unit this is a very good idea. When I first started P.E I purchesed a generic static streacher. It had a single rubber strap at the front and a hard plastic base that pushes against the fat pad. The concept was not bad but it needed much more traction.

If I may make a suggestion that would make attaching and detaching the apparatus easy. What about gluing or clamping the two barrell expanders to two cable clamps?

Can you put together a detailed parts list us? I must not be the only one looking for that extra inch.

This thread caught my eye because I built one of these also thinking about static progressive stretch. I’ll upload a pic of it. I use two hose clamps, a vacuum cap and foam on the proximal end. I used liquid weld to join the metal parts for easy tighten/loosen and to attach the turnbuckle. It’s an intense stretch that can be increased by small increments. Not trying to hijack this thread at all just thought I would contribute my version.

You don’t care, others could. The first one who had this idea, for example, you know presenting others’ ideas as yours own it’s somewhat like stealing.

Applying the force at two different points of the penis at the same time is an idea AKA a concept. So the two-way-stretch is a concept, not at device. Understand what you read please.

I realise that you aren’t gifted for words, but in English when you end a sentence and start another one the next letter should be in capital letters. Exactly as it is written in the forum guidelines.