Getting a pump, help.

Considering my measurements of about 7 inch BPEL and about 5 inch girth, going for length I should get the 1.75 diameter tube? But, should I get 2 inches or 3 inches longer? I don’t know which, and the advice on the sticky was not explained as to why.

Any recommended pumps? Less than $200, hopefully.

Thanks!

1. 1.75” would be good.

2. 2-3” is recommended because you might get discouraged with a larger tube, 9” tubes are easier to find but either would work just fine.

3. LeLuv is good, fair price and quality.

Hey man I had 5 EG when I started pumping 2 months ago, I bought my cylinders from Penis Pumps - Adult Novelties - Products

I got 1.75", 2", 2.25. Now I am almost packing my 1.75 cylinder so you are good to go with picturebrite

What type of cylinder should I get? Flared, hardwall, elliptical, etc?

I’m moving towards a metal pump. Good idea?

I just updated the link for the $25 brass pump from Harbor Freight.

iamaru - Lap pump = harbor freight tools pump

If your focused on length go with an elliptical thick wall cylinder, I just ordered one from Vacu-tech. Also be advised any cylinder bigger then 9” is more money.

Also be aware that the VacuTech eliptical measures 1.75” (short diameter) by about 2.25” (long diameter) so it will accommodate girths well above 5”, probably up to 6” or more.

The representative told me to go with 1/2 x2” for me and I’m 5.50 girth…hope that’s not too big or enough to grow.

Makes sense to me.

This is for the Elliptical circumferences:

1.5” x 2” = 5.55”

1.75” x 2.25” = 6.33”

If it accommodates much more girth, wouldn’t that be bad for length gains?

If I understand correctly, an elliptical with its varying diameter, its more for the baseball bat look? Sorry, I don’t quite understand why it has two diameters, I know the “tapered” cylinders are thinner on the upper end. Which is why I thought of going for a straight wall cylinder, instead.

Should I get rimmed or rimless?

What is the advantage of a elliptical cylinder? Penisdepot don’t have them, so I’ll look at Vacu-tech.

1. Rimmed, it provides a better seal and is more comfortable.

2. Straight-wall vs Elliptical, most of what I’ve seen are for aesthetic reasons. The only real advantage I can see is if your penis is very elliptical at the base then you might have a better seal with an elliptical and vice versa.

3. Pumps are mainly for girth, length gains are a nice bonus if you get them.
I have not seen enough evidence that points to packing the tube as an effective length gaining method IMHO.

Well, my base is more rounded and I have a “large” dorsal vein. But from mid to top I’m more wide, less rounded, oval.
So, straight wall seems to be better for me, correct?

Should I get the 1.75 cylinder and the 2.00 then? How much does the penis expand inside the cylinder in length and girth usually?
If the length does not expand much inside the cylinder, maybe a 9” cylinder is too much?

With the 1.75 cylinder the most girth it can go is 5.25” I think. If that becomes “easy”, I should have the other cylinder near, right?

Just wanna be careful on what I get.

My MSEG is about 5” and about 5.5” when fully pumped and I am packing up about 1/3 from the base in my 1.75” round cylinder. Hope that helps in your decision making process.

The length of the cylinder really does not effect anything other than being too short to accommodate your length. You should be ok with any length cylinder that exceeds your BPEL plus 1 inch.

Hmmm