Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

How Do You Know When Its Time For Bigger Cylinder

How Do You Know When Its Time For Bigger Cylinder

So I was pumping this morning and I’ve been using my 1.75×9 Size matters manual vacuum pump and the head of my glans restricted me from going as far as I have been going into the cylinder . As soon as I had that issue I pulled out and out more lube on and it didn’t fix the issue. It has a tapered end so I could need a straight cylinder that doesn’t have a taper is kinda what I’m leaning towards. Any advice would be appreciated. I’ve switched to my 2”×9” cylinder until I get this figured out just cause its taper is bigger

Joining the question.

I’m trying out Tiltiest tip of grinding the packed cylinder for length gains.

But I think I might overpack him and I get edema lately.

Originally Posted by Thaaphexone

So I was pumping this morning and I’ve been using my 1.75×9 Size matters manual vacuum pump and the head of my glans restricted me from going as far as I have been going into the cylinder . As soon as I had that issue I pulled out and out more lube on and it didn’t fix the issue. It has a tapered end so I could need a straight cylinder that doesn’t have a taper is kinda what I’m leaning towards. Any advice would be appreciated. I’ve switched to my 2”×9” cylinder until I get this figured out just cause its taper is bigger

Yes, drag will do it, no matter how much lube you put on. Also, if you’re not venting out as you’re sliding your dick in, that will prevent it. So, if you don’t have space on the sides of your dick as you slide it, you need to provide another vent.

Originally Posted by Thaaphexone
So I was pumping this morning and I’ve been using my 1.75×9 Size matters manual vacuum pump and the head of my glans restricted me from going as far as I have been going into the cylinder . As soon as I had that issue I pulled out and out more lube on and it didn’t fix the issue. It has a tapered end so I could need a straight cylinder that doesn’t have a taper is kinda what I’m leaning towards. Any advice would be appreciated. I’ve switched to my 2"×9" cylinder until I get this figured out just cause its taper is bigger

I think you need a straight wall cylinder to solve your problem. I think this 2" straight wall will solve your issue.

Penis Pump Cylinder with WIDE Flange 9 Inch or 12 Inch Length, 1.75"-2

Also, use our cylinder sizing chart: Selecting Your Cylinder Size


The primary goal of PE should be to make your penis as healthy as possible in both form and function. If you do that, increased size will follow.


Last edited by gprent : 09-09-2021 at .

Originally Posted by Don Logan

Yes, drag will do it, no matter how much lube you put on. Also, if you’re not venting out as you’re sliding your dick in, that will prevent it. So, if you don’t have space on the sides of your dick as you slide it, you need to provide another vent.

Thanks I appreciate the advice. Seemed to help holding the air purge valve in as I inserted during my night session. Any advice on where to get a 1.75”×9 new cylinder? The LeLuv site I was told to get a 2” pump is sold out of the 1.75” cylinders.

So looking at the sizing chart, the 2” cylinder would be too large?


The primary goal of PE should be to make your penis as healthy as possible in both form and function. If you do that, increased size will follow.

At 5.5” girth you may need to use the 2” cylinder.


Start: BPEL: 7” MSEG: 5" | Current: BPEL: 8.25” MSEG: 5.75" | Goal: BPEL: 8.5” MSEG: 6"

1st Goal: 7.5" x 5.5" | Achieved: 01/15/2021 | 2nd Goal: 8.25 x 5.75 | Achieved: 05/19/2021

Progress Pics: Road to 8x6 | My Log: Daros PE Notes and Progress Reports | Routine: Hanging with FIRe

I was using a x30 bathmate but my dick kept catching on the sides even with lube. So when I upgraded to the Extreme I sized up to the X40. Now it’s like putting a motorbike in a jumbo jet hanger and my cock keeps pumping at a 45% angle and catches the sides again! The comfort pad comes attached to a straight slighly smaller than the tube sleeve, to align your penis in the tube, great idea, put it’s virtually impossible to get a decent seal while using it.

But, as I’ve decided to do length training only for now, instead of combined training, my pump woes will be a problem for another time in the far future. So I’ve spent £150 for something to sit in storage for when/if my dick reaches 8 inch in length. Oh well, it’s best to have your weapons in advance before going into battle I suppose.

What I Noticed About Edema

Originally Posted by randomnickname
Joining the question.
I’m trying out Tiltiest tip of grinding the packed cylinder for length gains.
But I think I might overpack him and I get edema lately.

I used to get Edema when I was pumping too fast and too much pressure. Now I’ve learned to go a little. Bit slower and not as much pressure.

Originally Posted by gprent
So looking at the sizing chart, the 2” cylinder would be too large?

No,You’re probably right on needing a 2” cylinder. I have been using my 1.75” cylinder since January and my girth has increased so it probably is about time to upgrade. I know the 1.75” cylinder is just a starting point cylinder. Bought a 2”×8 1/2” pump yesterday that has the straight cylinder so well see how it goes now

Top
Similar Threads 
ThreadStarterForumRepliesLast Post
How to know when its time to Move onktsevensPenis Enlargement Basics905-01-2010 03:10 AM

All times are GMT. The time now is 11:29 AM.