Pumping and testicles getting pressed against the tube

Every time I pump my scrotum gets sucked in the tube and my testicles are getting pressed against the base of the tube and it is smashing my balls. Sometimes it doesn’t bother me, but sometimes it hurts.

Is there any way to prevent this?

What diameter cylinder do you have?

2 1/4 I think.

The larger the cylinder you have, the more likely it is for your balls to get sucked into the tube. You would probably be more comfortable and avoid your current situation with a 2” cylinder. But if that is not in the cards, try to keep lube off of your balls and start with an erection and press the cylinder tightly to your groin when you begin pumping up.

I remeasured and it is 2 1/2. So it is pretty big. I did think that lube that got on the balls could be a problem for drawing my balls closer to the tube. I also try to pull the scrotum skin away from the tube while I am pumping to pull my balls away from the tube, but it could sometimes make things worst and it is just painful.

Have you ever tried full-package pumping?

I just started pumping 2 weeks ago after a 6 month break, however, I have the same problem when I penis pump. I use a 1 3/4” tube. If I don’t watch the pressure carefully, the tube will smash my nuts too. Even when I do manage pressures, some of my sack gets sucked in which worsens my turkey neck.

So every once in a while I’ll put my dick and balls in a 2 3/4” tube, for 2 10 minute sets. This way I don’t have to worry about smashed nuts, or scrotum suck. I also believe it helps out in the length department because I can really feel a good lig stretch while under pressure.

Hope this helps.

Is it dangerous to put vacuum pressure on your testicles? It is also making my turkey neck worst, which I think makes it even more likely for the scrotum to get sucked in more.

Exactly the routine that brought me my length gains. Don’t mean to hijack, but keep up the routine and you’ll gain.

Normally I find that pushing the cylinder down tight really helps against ball suckage.

If it’s a big issue maybe putting like a towel inbetween your balls and the cylinder?

Thanks for the advice everyone. I did a pumping session a few hours ago and made sure my balls were dry and that no lube was on them. I pushed firmly and it worked out a lot better. So the problem seems to be solved. Another problem I have that keeps creeping in on me is discoloration after pumping sessions and just discoloration in general. Is there any way to improve discoloration?

Also is full package pumping dangerous and could it cause infertility?

I’m getting ready to experiment with applying a foam seal at the base of my pump flange to give my nuts a break from being crammed. I’ll let you know how it works out. I have a slight turkey neck as well and it does make pumping more of a challenge.

To reduce discoloration, reduce pressure. Try pumping at 4”hg for 10 to 15 minutes per cycle.

Full package pumping should also be done at lower pressures of 3 to 4 “hg and it is not dangerous or causes infertility as long as you don’t go crazy with high pressure.

Do you think I will still get good length and girth results at lower pressures and shorter workouts?

Full package pumping still kind of gives me the creeps, but I will consider it if it could help me yield better length gains and if it is safe.

Who said anything about shorter workouts? How about 3 or 4 15 minute sets at 4”hg. I would even say take it easy doing that, because 3, 15 minute sets at 4”hg gets you a lot of girth.

Just start experimenting with lower pressures. For me, my break through with gains came when I finally gave up on high pressure stuff and learned how to avoid trauma with low pressure. It really works miracles. Or at least it did for me.

I had this problem until I used a portion of one of Monkeybar’s silicone sleeves at the base of the penis. It not only kept the testicles in check but caused a better seal as well.

Rhadames