Pumping Underwater

:-k

I wonder why they don’t make the Deluxe Pump (which I have) water compatible?

Thank[b[rent[/b] for letting me know that I can till mist. I have continued to release the pressure and take my dick out, mist it and then continue pumping. Earlier today, I noticed that some moisture was showing in the tubing (like it had done before), but it was not like water was being syphoned into the cylinder. There was not that much moisture in the cylinder, just the liquification of the lube by the misting. This is how it as always been.

I never meant that I put a lot of water into the cylinder, not more than a Tablespoon or so, if that much. Before, there would only be enough water to run up and down the sides of the cylinder to get the lube working again, but that was all. The warming of the cylinder with a hot rice sox, also helps to keep the lube working. Especially if I use Vaseline, which sometimes I do.

Is that okay?

The harbor freight pump is water compatible with the water-cylinder added on, which should come with it. Also another good water pump is Mityvac 4000.

A question for all of the experienced water pumpers; how strong is the pressure/seal of the cylinder against the body?

Is it strong enough that you can pump while taking a shower and not have to worry about the cylinder falling off?

I’ve also heard that water pumping helps prevent the donut effect, any truth to this?

Stormy,

Yes the seal should be strong enough to take a shower, I do this as part of a warm down. I add hot water to the tube (you have to experiment with how much to add so that when you put your penis in you have room to pump without the water entering the pump) then pump up to about 2hg which will keep it in place while showering. The water in the tube will remain the same temperature as the shower water (as long as you keep it passing through the water as you would normally while showering)and it will give you a great low pressure warm down.

The key to keeping the water out of your pump is to make sure that the water is at the bottom (down by your pelvic bone) and hold the tube straight up so you are pumping mostly air.

If you feel that you gotten any water in the pump just spray a little WD40 in the end of the pump and pump it about 20 times, it will displace the water and lubricate the pump parts, probably a good thing to do anyways every once in a while.

P.S. Another thing that is great is to pump in the Jacuzzi, you’ll come out huge. :D

If you have a silicone sleeve in the cylinder, pull it out and snip a small hole in the end.

Fill with completely with hot water and insert when erect. The volume displacement and vacuum will suction the water out of the sleeve and into the space between the sleeve and tube. This seems to result in a shrink wrapped that reduces lymph buildup.

I thought you could use pretty much any pump as long as there is a reservoir between the pump an the tube?

Like the ones you get with a brake bleeding kit so the condensation/water goes in there rather than the pump/tube.

I’ve tried filling the cylinder with just enough water that when I’m in it & fully pumped there is still at least a 1-2” air gap. This feels wonderful especially when I’m pumping in the spa!!!

For any of you who have not read any of my previous post , you do not need a pump to creat a vacumm. All you need is to suck on the end of the hose /pipe . This works especially well if you want to do it under water ,in a bath or spa.

Myeight, I’ve been doing that a lot since I’ve read your last post, so thanks. I’m not even using the pump at all anymore! I kind of wish I had just bought the cylinder/tube now!

Good one Random , Now to keep up you interest in the subject ,try making your own cyl/tubes, Different sizes , flared ends etc.

That doesn’t sound like a bad idea because yesterday when I was trying to do water pumping (second set, my first set was just air) I couldn’t get into my 2” cylinder I just bought!! So I may want to make a bigger one. Only problem is that I don’t know how I would make a cylinder/tube because I’m in a college dorm and I wouldn’t know how to make them myself anyways, sounds like it would be tricky.

What I have been doing is using your sucking method for air pumping, and I’ll do it in the shower. I will then catch hot water in my mouth and release it into the tube haha, seems to work pretty well, and I get that extra heat. Then I will tilt the tube upward so I can suck just air out and keep the warm water inside.

Hey guys,

This is kind of a related thought. I’ve been PEing for years and I’ve been getting into pumping for a few months now. As we speak I’m trying out something that I’ve been contemplating for a while now. After a normal pumping session, I put myself in the pump with some water and pumped up to about 2” Hg (pretty much exactly what kdoc described). Only I’m just sitting here and doing some research and browsing the Internet. So, considering the great stuff I’ve heard about ADS in general, I’m more or less trying to do an ADS type thing that’s more girth-focused. I’ve had bad results with girth wraps ADS because with me it seems I’m either cutting off too much circulation or not doing anything; I’ve tried a lot.

I’m about 6.75” long erect and the pressure has only been strong enough to keep my flaccid at 5.75”, which considering I’m a grower with a pretty small flaccid, it’s pretty good I think.

Do you guys think this makes sense?

Some people claim that the way to make gains with pumping is by staying erect during the process.

I do pump erect for my actual working sets. But after them I’m thinking of doing this to try to force myself to do more of the healing in an expanded state.