Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

7 inch girth - true or false

Originally Posted by thoughtfulgold
I can say I’m still using a 2.25” Cylinder for the same reason. And at low pressure, 2-5HG, it fits comfortably around my base.

I do not know how much you expand though. So you may be fine with the 2.25” Honestly 2” is a touch small BUT what brand are you using or planning on?

2.5” is a bad idea. That’s the same cylinder size that caused the issue I have. And there is a lot of issues with sealing early on unless you start high pressure.

LeLuv


4/16 BPEL 7.2 MSEG 6.0

1/17 BPEL 7.75 MSEG ~6.2 BEG 6.75

Size anxiety is the mere response to viewing other males as a threat and the corresponding jealousy it causes. Realize that your feelings are a response to a perceived threat and the anxiety will disappear. My log: Big Booty Extravaganza (and Log)

Originally Posted by BigBootyFan
LeLuv

Okay. Looking at them, I notice no gasket on the bottom or cushion. If that’s fine with you, that’s good. However, because I use a VelSeal 2.25, I know that the cushion on the bottom makes a difference in how well they can seal. Meaning, I would recommend a VelSeal 2.25 in your case OR a LeLuv 2 at this point because both would seal roughly the same. As the VelSeal has some more ability to seal with that large cushion at the bottom and it would allow you to get into a larger cylinder without having as many sealing issues as one without said seal.

I’m not familiar with LeLuv, as I haven’t pumped with them before, but I am familiar with how tubes with no gasket at the bottom tend to seal. The picture I saw of the LeLuv suggests it is just the tube so…I’d go with a 2” diameter for now.

So, if I had to give my recommendation, I’d say go with a LeLuv 2” and be prepared in the next 6 months to move to a 2.25” from either manufacturer, since you’re going for narrow tube style pumping.

Are you going high pressure sets? Low to high pressure? Or strictly low pressure?


Now: 9" BPEL x 6.25" MSEG as of 11/10/2019 This is my story, a few progress pics of me here, and all my methods.

Then: 6.25" x 4.37" in 8/2009 Are you new to PE? Here's some advice I wish someone had given me when I first started.

My Extender and forward to 10" and balls enhancement project. There is no "Holy Grail" of Penis Enlargement. Only time and effort works. I'm *10* years in and counting. All you have to do is put the work in and keep the faith.

Originally Posted by thoughtfulgold
Okay. Looking at them, I notice no gasket on the bottom or cushion. If that’s fine with you, that’s good. However, because I use a VelSeal 2.25, I know that the cushion on the bottom makes a difference in how well they can seal. Meaning, I would recommend a VelSeal 2.25 in your case OR a LeLuv 2 at this point because both would seal roughly the same. As the VelSeal has some more ability to seal with that large cushion at the bottom and it would allow you to get into a larger cylinder without having as many sealing issues as one without said seal.

I’m not familiar with LeLuv, as I haven’t pumped with them before, but I am familiar with how tubes with no gasket at the bottom tend to seal. The picture I saw of the LeLuv suggests it is just the tube so…I’d go with a 2” diameter for now.

So, if I had to give my recommendation, I’d say go with a LeLuv 2” and be prepared in the next 6 months to move to a 2.25” from either manufacturer, since you’re going for narrow tube style pumping.

Are you going high pressure sets? Low to high pressure? Or strictly low pressure?

I’m definitely starting low. Especially after seeing the post you linked yesterday where another member was overpumping and caused severe damage.

Thanks for the input. I’ll definitely look into VelSeal!


4/16 BPEL 7.2 MSEG 6.0

1/17 BPEL 7.75 MSEG ~6.2 BEG 6.75

Size anxiety is the mere response to viewing other males as a threat and the corresponding jealousy it causes. Realize that your feelings are a response to a perceived threat and the anxiety will disappear. My log: Big Booty Extravaganza (and Log)

Originally Posted by BigBootyFan
I’m definitely starting low. Especially after seeing the post you linked yesterday where another member was overpumping and caused severe damage.

Thanks for the input. I’ll definitely look into VelSeal!

Starting low pressure, especially if you’re going to ride it low pressure regularly, a 2” from either manufacturer should be fine.

I chose Pumptoys VelSeal after using a couple of Vacutech’s Thickwall and Elliptical and getting serious pain, then using CTC’s cylinders (which are made cheaply to save on cost and make it easier to upgrade to but don’t use male to female connectors and flex more than I’m comfortable with) before coming to PumpToys and getting a VelSeal 2.25” and 2.5” (which honestly doesn’t fit but around the base doing mid to high pressure work) and not looking back.

You won’t regret your choice with the VelSeal in my opinion. I can pump much longer with the cushion on the bottom and for length work with a pump (which isn’t optimum for length but you know this) time clocked in the tube in total is paramount.


Now: 9" BPEL x 6.25" MSEG as of 11/10/2019 This is my story, a few progress pics of me here, and all my methods.

Then: 6.25" x 4.37" in 8/2009 Are you new to PE? Here's some advice I wish someone had given me when I first started.

My Extender and forward to 10" and balls enhancement project. There is no "Holy Grail" of Penis Enlargement. Only time and effort works. I'm *10* years in and counting. All you have to do is put the work in and keep the faith.

6 Inches Length 7inches Girth

Dick measurements

Flaccid length 7.5cm 2.9 inches

Flaccid girth 10cm 3.9 inches

Stretched length 4 inches

Erect length 6 inches
Erect girth 7 inches
Base girth 6 inches

Balls

2 inches length


Last edited by LittleEngine : 01-24-2021 at . Reason: No penis pics in public forums.
Top

All times are GMT. The time now is 02:14 AM.