Water in the Cylinder And Filling The Tube

Hi thunder’s place, just wondering if water pumping in a cylinder prevent us from reaching the end of that tube, for instance, does getting warm water in my 9" tube block me from getting 9" ? Do we need longer tube to perform water pumping ? What’s do you think ?

Hey there brother! In my experience, No. I have actually been seeing bigger numbers in tube since adding warm water. I started air pumping at about 7.25" Now I am reaching 7.6"-7.7" in a 2" diameter [6.3" girth] cylinder.. I feel like adding warm water is a great addition!

Yeah I know that warm water help to expand but like it fill a part of the cylinder so less volume will be available for your penis in the end ? Correct me if I’m wrong.

It won’t stop you from growing.

Your dick will displace the water, not the other way around.

Does it mean at some point my dick will force the water to leave the cylinder ?

You dont want water leaving the cylinder so you must experiment and find out how much water you can add to the cylinder which will allow penis expansion and keep all the water in place.

This is the only example I can think of where a 12” cylinder is helpful.

How do you add water to an air pump? I would like to do this as well.

Hi bro, this post was made by 32quarters

Make sure the fluid reservoir is positioned in line between the cylinder and the vac pump. Longer tubing is helpful in this activity. Then you have two options: (a) get in a tub of warm water and slide the cylinder over your penis allowing water inside, or (b) while sitting or standing fill cylinder with warm water and continue as in (a). Don’t fill the cylinder completely up. You need to allow an air gap because when you engage the vac pump air will leave and water will rise. Always keep the pump higher than the top of the cylinder. Make sure the water does not enter the pump, and probably not the tubing because the volume of water is small and will get to the pump easily if its in the tubing. If it does, release the cylinder and start over with slightly less water in the cylinder.

And this one is from bemorethanbig

I do water pumping not standing but sitting on the bathroom floor. I fill hot water and leave some space in the cylinder, I now know the right amount of space to fill up, I leave that to the side, then get as hard as possible, be on my knees, point downwards get the cylinder on, and then sit down, with just your hand pressure you should get no spill, the water goes down and the air is all on top and then pump out the air until the water gets to the tube (I have a 2ft tube?, longer than usual), after that you can sit or stand whatever. I don’t stand because if there is an air pocket it touches my dick and I don’t like it, I need to invest in a longer cylinder to get more water in so even at an angle I still only get water. I have a routine that I never get the floor wet and when I place it in and out I get no spill. I can’t explain it but you will find the gear and style you like. So like many here, you find a way to not get water everywhere, and even if there is a bit of spill it’s nothing an extra towel can’t handle. I’m so comfortable now that I could do this on my bed, I don’t have to stay on the bathroom tile.
In the future I will def get a bathmate when I am done with my PE growth and then to maintain pumping for life, but right now, I need to know the gauge and cylinder size difference, I am seeing what works for me and my gains best.

I hope this will help you

In general, longer tube seems to be better for water pumping right ?

Longer tube is better to a point. Essentially you need a couple of inches of air gap between the water column and the valve at the top of the pump so when you pump you remove air from the cylinder and not water. When I do this I keep the tube pointed up so the air is at the top.

Be sure you are using a gauge. The amount of vacuum increases really rapidly when the tube is mostly filled with water rather than air.

I also recommend practicing this in the bath tub or shower until you get the hang of it since there can be a lot of water on the floor as you’re learning the technique.

Good question, as far as girth, you will know when you are up against the cylinder and when you have water around it. That is why I recommend getting two different cylinders. One that fits just right and one larger than that.

No, water doesn’t prevent any gains. I can understand that you are thinking of water pushing up against you but it’s more like you are trading air for water.

Small disclaimer, I have yet to buy a longer tube than the recommended one from LA pump, I don’t know yet what an inconvenience it will be to add another inch to how I sit. I will say this, get two cylinders.

The one that fits just right, get that 1 inch longer.

The one that is one size up in girth, you can keep that at the recommended length because you have enough water in the chamber.

I have yet to try this, though

Yeah I think I will get my hand on a 12" tube, I’ll be able to fill it with more warm water