Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Cock Coil ADS

Hi BeardedDragon,
I am not English speaking people so I don’t understand what is HTW, could you look at the picture I attached in this email and tell me what kind of wearing for this Cock Coil ? Hooking to the ball or tight it to the glans of the dick head ?

Thank you!

20160405_115102.webp
(22.5 KB, 74 views)

Ah, no problem. I haven’t seen your picture yet, but perhaps the pictures in these topics will help you.

This one explains the HTW = Hair Tie Wrap.
HTW: its a wrap

And this one has pictures of the Cock Coil in use with the HTW.
Cock Coil Pictures

And this is a link to another picture of two Cock Coils + HTW.
Tiger10 010.JPG


Before 5.5" x 4.1" ///////// Now 7.4" x 4.9"

Thank you BeardedDragon! So It will not hook to anything, just tight to the wrap.

You’ve got it. It’s a very good ADS. With the correct tightness you can wear it all day and even urinate with it on.


Before 5.5" x 4.1" ///////// Now 7.4" x 4.9"

Quick question regarding the shrink tube.. For sizing, say on the 1/4” and 3/16” lead wire, would you need a 1/4” and 3”16 inch shrink tube to properly fit the lead tube when shrunken down with heat?

What is the preferred/recommend size for the shrink tube for those two measurements?

You need something just larger than your lead wire. When you buy the shrink wrap, it will say by what multiple it shrinks, the stuff I bought was designed to shrink 2-fold, and so I bought 1/4” shrink wrap for the 3/16” wire, and 3/8” wrap for the 1/4” wire.


Before 5.5" x 4.1" ///////// Now 7.4" x 4.9"

As can be relied upon, BD has it exactly right.

xeno


originally: 6.5" BPEL x 5.0" EG (ms); currently: 9.825" BPEL x 6.825" EG (ms)

Hidden details: Finding xeno: a penis tale; Some photos: Tiger

Tell me, o monks; what cannot be achieved through efforts. - Siddhartha Gautama

Well I constructed to CC with no problems.. My next issue is keeping/tightening the CC on. My flaccid size is on the smaller side about 4x4. I’ve tried the HTW method but it just keeps pushing the rolled up wrap up over my corona, its just gripping the skin and my skin just end up bunching up big time near my glans. Which after about 20-30 minutes of wear begins to cause series fatigue in terms of the bunched up skin and trapped blood.

I have noticed that if I wear a silicone sleeve, it seems to eliminate all the sliding and tightening problems. It grips perfectly with the sleeve. Does this eliminate some of the effectiveness for the CC? Obviously I want to get the full benefits of using the CC, will the sleeve retract some of the positives of the CC or does it really matter?

Shouldn’t matter Longdong. Sounds like you need to use a little more compression along the shaft; retention should consist of both retaining from the bunched up HTW+bunched up tissue AND compression along the shaft underneath the CC.

Are you circumcised?

xeno


originally: 6.5" BPEL x 5.0" EG (ms); currently: 9.825" BPEL x 6.825" EG (ms)

Hidden details: Finding xeno: a penis tale; Some photos: Tiger

Tell me, o monks; what cannot be achieved through efforts. - Siddhartha Gautama

Thanks for the reply Zeno, that could be the problem that I’m just not tightening it enough, it sure feels like it though. I am circumcised so I don’t have excess skin. I tighten from the glans down to the base. The skin on my shaft just seems to slide all the way up to the glans, even with decent compression of the CC. When I do wear the sleeve with it, everything is then fine, I can do jumping jacks with it on with no problem haha.

Jumping jacks…that’s good :) . Sounds like you’ve engineered your own solution but one more tip: the Scunci model #212087-A hair tie is sufficiently stretchy to use as the second HTW; when used this way, it can be stretched over the distal end of the CC…thereby providing excellent retention of the CC. The CC can’t slide down the shaft because the 2nd HTW, upon which it must slide, is pinned underneath the CC…AND stretched tight over the CC. I’ve gone jogging with this configuration with no appreciable slippage.

Good luck and keeping working at it, you’ll get it dialed in.

xeno


originally: 6.5" BPEL x 5.0" EG (ms); currently: 9.825" BPEL x 6.825" EG (ms)

Hidden details: Finding xeno: a penis tale; Some photos: Tiger

Tell me, o monks; what cannot be achieved through efforts. - Siddhartha Gautama

Four CC stack:

xeno

CC1.webp
(135.5 KB, 65 views)
CC2.webp
(126.1 KB, 43 views)
CC3.webp
(141.9 KB, 43 views)

originally: 6.5" BPEL x 5.0" EG (ms); currently: 9.825" BPEL x 6.825" EG (ms)

Hidden details: Finding xeno: a penis tale; Some photos: Tiger

Tell me, o monks; what cannot be achieved through efforts. - Siddhartha Gautama

Originally Posted by xenolith
Four CC stack:

Xeno

Hey xeno, I’ve been looking at Cabela’s to buy some solid lead wire and the heat shrinkin tube, but found out that I’m going to pay 2,5 times the value of the items for shipping and charges,(yea my country sucks donkey balls) Itens: USD 27,96 Shipping:USD 64,40.. Maybe for the absurd amout I would have to pay, there would be any chance for you to sell me some of yours CC’s for a more nicely value?

I want to try it very bad, but this shipping and charges are just ridiculous

Sorry bigzin; I’m not going to do that. I encourage you to make phone calls to fishing stores and ask for “pencil lead”; most should carry it.

Good Luck!

xeno


originally: 6.5" BPEL x 5.0" EG (ms); currently: 9.825" BPEL x 6.825" EG (ms)

Hidden details: Finding xeno: a penis tale; Some photos: Tiger

Tell me, o monks; what cannot be achieved through efforts. - Siddhartha Gautama

Hehe, that’s fine, I’ll end up buying it anyways, maybe next month.. I don’t think that I’ll be able to find it here since I already looked out on the internet trying to find it(on my country), and did not had anything like “solid lead wire 1/4”

Top

All times are GMT. The time now is 01:05 PM.