Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

PenisMaster Adjustment Help Requested

PenisMaster Adjustment Help Requested

Hello,

I have searched high and low, yet my efforts remain fruitless. I have yet to fully figure out how to adjust the extendors on my PenisMaster.

I have searched this board, other message boards, PeniMaster and PenisMaster sites. I have looked at the PeniMaster and PenisMaster directions. I have tried playing the DVD, but it does not work well on a Mac and it does not play in a DVD player as I tried. I have watched videos on here, and STILL, no luck.

Basically, I am looking for a comprehensive guide to help me out. The trouble I am having is that it will simply start to unscrew the rod or “piston”, and just make the overall length higher, not adjust the tension. Eventually, it will unscrew itself. I have tried holding onto every other rod while adjusting, to no avail. Nothing seems to work! I have spent quite a lot of time trying to figure this out, this is not a thread I am making after only experimenting a little bit.

Please, if you feel you can explain the technique BETTER than it has been explained on here and elsewhere, please please do so. I am getting desperate, because I am a firm believer in progression, and adjusting the tension would allow me to do so easily, which is the reason I bought the PenisMaster in the first place.

Thanks,
Polymath

Originally Posted by Beginner91
The trouble I am having is that it will simply start to unscrew the rod or “piston”, and just make the overall length higher, not adjust the tension. .
Thanks,
Polymath

Beginner, this IS how you adjust the tension. The pistons are spring loaded so when you unscrew the rods it puts more pressure on the spring giving you greater tension. You will notice that the more it is unscrewed the harder it is to push the rods down. You don’t need much tension to start. Once you work your way up to the maximum tension you can add a 1/2” rod and start the tension all over again.

Hope this helps.


Let me tell you the secret that has led me to my goal: my strength lies solely in my tenacity.

Louis Pasteur

Which direction am I screwing? I tried screwing counter-clockwise, but the adjusting rod would unscrew itself before getting to one line. So, if I can’t even test out the max tension how could I ever progress to the max tension? What it looks like to me is not what it looks like in any manual. The adjusting screw that attaches to the base (not the adjusting rod aka piston), in the manual, looks like it is supposed to be screwed up along with the piston, but then that would run out of room as well.

Both ends have threads. Start with both screwed completely in. Adjust tension by turning the screws clockwise (left.)

The screw base (part your fingers are turning) should move away from the base. Both ends will unscrew a little. The cylinder will

compress and less lines will show. You should feel the tension getting tighter. If you are not, maybe you need to add another bar. It should be a challenge to stretch your penis out far enough to get in on. It only has about 1/2” of play, if you get above that you need to add a bar.


Let me tell you the secret that has led me to my goal: my strength lies solely in my tenacity.

Louis Pasteur

Iguana, when I unscrew it, it just gets looser. The screws get looser, and it becomes more flimsy as the whole thing isn’t attached tightly. Could I have a defective unit?

I don’t feel any tension increasing, and also when I unscrew it, I can see the threading of the screws. When I unscrew it, it just gets longer, there are less lines, but that is only temporarily, as it will expand and all the lines will show again.

It doesn’t sound like your unit is defective. I think you are misunderstanding how it works.
I have attached a simple drawing for reference.

The cylinders are spring loaded, when you unscrew the screws both the top and bottom threads will loosen.
The effect is that the top portion of the screw (shown in red) will push into the spring. This adds pressure to the piston
and puts greater force on your penis.

Originally Posted by Beginner91
When I unscrew it, it just gets longer, there are less lines, but that is only temporarily, as it will expand and all the lines will show again.


That’s what it supposed to do - get longer. If you are having to loosen the screws so much it get’s flimsy then you need to add a 1/2” rod.

Does this make sense?

PM Cylinder.webp
(11.2 KB, 65 views)

Let me tell you the secret that has led me to my goal: my strength lies solely in my tenacity.

Louis Pasteur

I took another look at my PM and my diagram is a little off. The screws do not push into the springs directly. They push into the bottom half of the pistons. Here is a corrected copy of the diagram.

PM Cylinder.webp
(11.2 KB, 53 views)

Let me tell you the secret that has led me to my goal: my strength lies solely in my tenacity.

Louis Pasteur

Adding a 1/2 inch rod would be very difficult to stay in place, unless I used like monkeybar’s vacuum sleeves and tied it to my leg.

Thanks for the diagram, though!!

You might want to check out http://www.x4labs.com as they have some videos and a support forum

Penis Master is the same as X4Labs product

Top
Similar Threads 
ThreadStarterForumRepliesLast Post
PenisMaster Help!!IguanaPenis Extenders905-22-2013 04:13 AM
Penismaster ProblemMichael34786Penis Enlargement901-29-2008 12:12 PM
Penismaster - stop strap slippageJetAtkinsPenis Enlargement205-29-2007 08:33 PM
A good PenisMaster routine?TheSkepticPenis Enlargement108-29-2003 06:25 AM

All times are GMT. The time now is 02:21 AM.