Convert noose extender to something else

I have an andro-penis extender, and while I really like wearing extenders, the noose system is very flawed.

The noose constantly slips as the strap and comfort sleeve deteriorate quickly (literally after a month, the strap constantly slides out of the holder or the hole). I want to convert it to a vacuum extender, or another type of strap that actually holds in place.

But I have no idea where to start looking. I’d prefer a vacuum extender, but those are expensive for the whole set. The rods and base of the andro-penis work perfectly, it’s just the nose I want to replace. Any ideas where to look to get just the one part that will fit the andro-penis?

You can check out autoextender.com. They have one there.

Yes you can get a vacuum head at auto extender which should fit your extender as Dave Frenzy advises

Another option is to do a DIY velcro strap mod such as described here

http://www.pegy m.com/articles/ … penis-extenders

Trying to Make it Better - Velcro Extender Mod

Austfred

Velcro strap is cheapest & easiest mod.

I’ve been around for a while. I was on this forum in the early 2000s but life happened and I forgot my username and passwords. Eventually had to create a new profile. But I’m wondering if there are any pictures that show how to set up the Velcro… I have an original Andro penis and a newer one that uses a nose/ strap rather than just the noose. But it still slips and keeps me from being able to do more than an hour or so unless I’m completely still…

I hit the last listed link above and there are some photos in that chain. Seems a simple and elegant solution. I switched from a vacuum head attachment to this premium strap style, but found the device doesn’t always hold the straps well. I use a silicon sleeve piece below my glans then wrap the included silicon strip as well before strapping in, and lately found that a simple binder clip added to the parts of the straps that protrude from the bottom of the head piece do keep them secure. But, I may have to try this Velcro mod as it is simple and will likely outlast the straps.

I finally got around to buying some velcro stripping to try this modification to the PeniMaster strap-connector. Wearing it now, and all I can say is so far it’s a phenomenal modification. I wrap just below the head with a silicon sleeve section, then use the silicon wrapping that comes with the device. With that protection in place there is no issue with any scratching from the velcro or skin pinching. And, the head stays where it’s supposed to be for a great, steady stretch! I posted a few pics in my progress (members) section as I appear to show some stretched gains.
Bottom line is this velcro set up so far may be the answer!

If you get a vacuum head, whether designed for hanging, waist straps, or extension, you can probably drill a hole in the plastic and use an S-Hook to attach.
You’ll end up using a lot more rod-length for the setup and could run into interference issues where the vac-head is wider than the rod spacing, but it’s probably doable.

Alternatively, give ResQTape a try. It works great for me and others with a noose setup.

I bought a cheap extender from Ali Express that included the glans attachment that had the space in it for Velcro straps. I used that strap attachment with my Andro penis and had to use two of the rods from the knockoff. The rods are smaller in diameter but the treads on the rods fit… I then used a piece of sponge foam from the Andro kit and used three squares of toilet tissue to fold horizontal and wrap where the glans and shaft meet… I’ve been able to wear the Andro with Velcro and foam sponge plus tissue for 6 plus hours for the last 3 days…

The result is a nice comfortable tug. I have a left curvature. So I get a warm sensation on the left side of the penis… It actually feels pleasurable… Before the mod I could only do 1-2 hours. And if I moved the thing would fall off. It was painful and pinched me all the time… The only difficulty I’ve had is with sitting and standing from my car. Getting in and out of my truck is no problem. In just a few days my flaccid hang has increased visually… Thankyou I’m very happy… Your help is appreciated…

Other thoughts… Has anyone had any real feedback or results with Restorex?? I see posts but no one has updated anything…

Thought I would share the elegantly simple retrofit I am using. The first photo shows the strap that came with my high quality German device….throw the strap away. It will slip. Period. And I read here about many others’ problems with slippage, etc. While the velcro stripping I am using as a substitute is easily inserted into the slots on this device, I am sure there would be ways to engineer a similar solution to devices with other connection methods (noose, whatever). The bottom line is this modification allows the penis to rest directly on the sled surface, and the velcro very simply wraps around to be tightened as-needed. I put on a fabric sleeve followed by latex to be sure I am protecting the skin, and to allow good pressure. It. Just. Doesn’t. Slip. There may be times you need to readjust, especially if the latex sleeve slides up a bit, but that’s far less frequent than with the original strap, and the velcro strap will not stretch upward with tension. And, the ease of application/attachment is incredible, compared to as-designed. Just my two cents.

Vacuum head could be attached using the noose.

Basically just clamp the vac head with the noose or other strap and it won’t slip cuz you can really clamp the heck out of it.
Could even use a hose clamp to secure it…

Thank you for this mate

Most welcome!