Homemade Extender the Lightning Rod

Hey guys. I’ve seen a couple extender designs pop up in the last week so I couldn’t help throwing mine into the mix.

I think it’s really great that people are putting their ideas out there! :)

First off, this is not an all day stretcher! This was designed quick on and off use for stealth PE when time and privacy is limited. I wear it for an hour at most, but do not have any problems with it during that time and could probably wear it much longer if privacy concerns were not an issue.

Secondly, it is not designed to be concealed! I believe you should be constantly monitoring any type of PE!

With that said, here is the design that I have been using since January. It is a cleaner, simpler version of the White Knight 2.

It is cut from a block of 1" thick plastic but I am sure a chunk of hardwood might work too.

Same "Chicago screw" post and closet door springs as the old design.

A piece of 3/8" plastic tube fits loosely over the posts and between the springs. It’s length is cut to determine the amount of tension is applied by the springs (longer equal more tension).

The loop is 1/4" surgical tubing with a flat shoelace pulled through it which gives support without the tubing twisting or rolling off.

The loop is rigid, no flex at all, and once set to the right size, braces the head against the rounded top of the extender securely while allowing circulation, mimicking a overhand manual grip (where the top of the extender is your thumb and the tubing is your finger. After it’s initially set it fits the same every time you put it on without readjusting, which speeds up the time it takes to condition yourself to the fit (gets comfortable sooner than other methods). To see how it works check out the White Knight 2 in Action

The base has two levels to quickly adjust from a standard and low tension set. For example, start in the lower level as a warmup, then jump to the higher level to increase the tension for the rest of the set.

I think the attached image is pretty straight forward and I am not going to go into too much detail with it because I am actually finishing up a new extender that addresses some of the limitations of this design, mainly the adjustment issue (This design needs to be taken apart and a new piece of tube put between the springs to accommodate an increase in penis size).

I am hoping to put that new design up in the next couple weeks, but in case I get hit by a truck before then, here is this one for now.

It has served me pretty well. ;)

Here is link to the Member Pics section showing the Lighting Rod in use.

(Yes, there was a time in the not to distant past where the plan was to make and sell these, but that time has past. It is much more satisfying to inspire people to build their own and save their money than it is for me to lose my time and money trying to make them!)

Edit: Check out the easier to build "tube top" head piece introduced later on in this thread. :)

Looks like a nice piece of work !

Nice as always. How much force can pull an extender like this, out of curiosity?

Thanks, as always.

I use it very comfortably at about 5 pounds (2300 grams) of force. The springs are quite strong and the device is very sturdy so it can be increased much further (8 to 10 lbs easily) but I do not think the “quick noose” system would be ideal for tensions much higher.

I would only recommend going higher than 5 or 6 pounds if it was modified with a different head attachment (such as a vacuum head, or something similarly used in typical hanging) and possibly a thicker base to spread the force out a bit more.

Fortunately, the design easily allows for changes such as this.

The next design is better suited for the possibility of higher tensions as it will feature one piece solid rods as opposed to the rods of this design which are built up by 1” extension pieces.

I will try and get the graphics/instructions done for it this week.

Great, I am interested in it :D

Ever think of selling some? I’m horrible at making things

Sorry, I gave it lots of thought but I just can’t make it work with the situation and resources I have.

You’ll just have to get better at making things! ;)

Cantlook, I am so tired of seeing your extenders on here….. And you not making money :D Seriously man, you’ve got some great homemade inventions and concepts. Ever think of taking these a step further and making a prototype for a patent? Instead of pulling a Sayain and selling Home Depot devices for ridiculous prices, you put a $2,000 on paper and try to sell it to a company.

I’m thinking if were willing to put in the effort for a year or two you could come up with a few new improvements no one would ever think of. You could cast your own plastic molds or find a company to do it for you, and then combine them with ready made materials from hardware stores or hobby shops. It may cost you a few thousand over a few years but the result would be a light weight extender better than those commercially sold and copied by every sex toy company.

Great design

Could you perhaps take a picture wearing this?

I’ll see if I can find some time this weekend, but the link in my first post to the White Knight in Action thread has an “in use” image of a very similar device.

Cantlook - Very nice Homemade Extender. Exactly what I was looking for. Inexpensive and useful. It would be helpful if you can list the parts and develop some basic building instructions. I am semi-handy but would need some guidance. Many thanks!~

Thanks. I will do up some better instructions for this design as well as I work on the next one.

The Lightning Rod uses less of but draws from the same materials as the White Knight 2 so you can check out that thread for a little more detail as far as materials, for now.

Thanks Cantlook. Looking forward to the additional information.