Leluv Extenders

Thinking of getting a extender from leluv. They have 3 main types, spring, light weight spring, and screw type.

I have no experience with extenders, and of the 3 types what is the better.

Thanks Buggs.

Buggs, I recently bought a LeLuv slider extender. That’s the one with the screw rods. A was using a cheap proextender that was fine but bought the slider so I could try out the stress relaxation technique. I am very happy with it. I bought the one with the dual action cradle so I could fit a DIY velcro strap. Did the same to the proextender.

The only drawback I can see with the slider is that a newbie conditioning his penis would have to be more careful as you only have stretched length to go by. With the spring loaded ones you can gradually increase the tension as you condition.

On the other hand the Slider is easier to adjust as you tension up. You do not have to worry about the limited screw travel as with the spring type.

Austfred how dose it compare to the cheaper one’s, I was after one with the cradle like you said and just a step ahead of the cheaper ones in quality.

I’ve not used one before so I’m leaning to the rod type, I think. I’m after one that will last at least a year and not break in a month.

Thank you austfred. Sorry this is not in the extender section, but I’ve not got enough posts yet.

I also have a cheap chinese proextender I bought on aliexpress. The overall build quality is good and hard to say the Leluv one has any better build quality. If you want a spring loaded one I would go for that one. On the other hand the LeLuv Slider seems to be the only game in town if you want a threaded rod type unless you want to make your own as rootsnatty did. The dual head cradle is important IMHO and I have no experience with the 4 Way one but just ordered a cheap one on aliexpress (just the cradle) to see if it has any benefit over the two way.

I reckon there is little correlation between price and quality with extenders other than some of the pricier ones have extra functionality such as vacuum heads etc that may be worth paying for if you want that functionality (eg vacextender and penimaster pro). I gather there are some extenders on the market that may be more easy to break but do not believe the proextender is one of them. Search on aliexpress for “penis extender” and about 13 pages of offers come up. Virtually all of them are the proextender although I did see a weird one which uses an adjustable blue plastic tube encasing the penis to change tension but which uses the noose for attachment. Would avoid that one.

Thanks austfred, if their isn’t a lot difference between cheap and middle of the road, then I may end up getting the spring type, and then later the screw type may be a year down the track when my techniques are tuned in.

Thanks again

Hi Austfred,

You seem experienced with the cheap pro extender from aliexpress so a question if you don’t mind please.. Sorry if wrong thread.

How do you get the tension to work on there? I bought one and I start with everything screwed all the way down, then start unscrewing the bottom twist dial to increase the tension.. This makes the bottom rods and the rods underneath the hexagon tension markers increase in size however the tension markers never go in to indicate force.. It will either keep unscrewing till the rods come out of the threads or it will be so stretched that the penis pulls itself out.I’m baffled :s

Hi Stranger

>then start unscrewing the bottom twist dial to increase the tension

That is the way to do it. I suspect the problem you are having is that you are completely trying to stretch by adjusting the rods. I discovered to get a useful stretch I had to stretch my penis somewhat by hand before I clamped it in the noose or strap. Otherwise I would use up all the screw travel before I got any real tension. That is one benefit of the Leluv slider. You can clamp it in a fairly relaxed state and then keep screwing until you get the desired stretch. With the proextender, and I expect most other similar extenders I found after my penis relaxed after the initial stretch I often ran out of travel even when I prestretched. Then I had to unclamp and hand restretch and clamp.

Ok many thanks for your help, will see what I can work out!

I’m having the same problem. All I’m getting is a stretch where I can stretch to the point where the bars come loose and I have to re-attach them!

Sketch, As I mentioned earlier I found the trick was to do a hand pre-stretch as you mount the head in the noose or strap. That way you save the limited travel in the rods as you extend. Can be a bit tricky when you start but gets easier with experience.

I found the penis usually relaxes after a few mins in the extender and you have to adjust again. One benefit of the Leluv slider is that you have a large amount of travel and can even add rods without unattaching..

Thanks Austfred
I stretch to get the head to fit when its nice and relaxed and then use the bars to stretch and elongate the penis. But aren’t the tension bars supposed to get smaller (one notch being 900 tension, the next 1200?)

The manual certainly says so. I’ve gone as far as to attach the 2 small extenders to the original unit to see if by stretching even longer the hexagon like units would move - but they haven’t. So I’m really just stretching my penis (which is good - it theoretically does the same thing) but I’m not using any tension? The manual says the hexagon like bars are supposed to get shorter over time (you adjust). I’ve tried twisting them separately from the bars that elongate the penis but that doesn’t work either?

Okay so I’ve managed to twist / turn the hexagon like bar only, which seems to bring the head unit closer and farther to the beginning point (unlike the rods which stretch), but this doesn’t really answer my question and troubles when it comes to the tension. I’m not sure what this means? If the head of the unit is closer to the base does that mean it has less tension?

http://bestpeni sextender.co/pe … action-tension/

When I follow the instructions in the video it is saying that the RODS are actually for tension - not for extending the unit and then we turn the hexagon like bars to stretch?
But even when I try that - I take the rods all the way down to increase tension but I can’t move the hexagon bars without taking the cylinder out of the head unit. They are too hard and stiff to turn. When I am able to turn them while they are in the unit the cylinder seems to start coming out ??
I’m dying here!!

It is funny to see how similar these extenders are though.

Tension increases by using the adjusters to increase the distance from where you are strapped in and the base. As that tension increases the springs inside compress and hex sections move inside until eventually the marks on the side start moving inside. When the first mark reaches that point you are supposed to have 900gms of tension.