Penimaster Slippage

Hello guys,
I just bought my new penimaster for 300$ and i am actually wearing i wasted the money.
I slip out of it all the time i give it some light stretch.
I am uncut with a relatively long foreskin and i have a small glans, maybe thats the reason.
Somehow i cant produce right vacuum to hold my glans inside.
When i try to stretch it just gets rolled out of the chamber and my foreskin rolls over the glans.
I tried the small Split Adapter, didnt help… in the big Split Adapter i cant get in.

Please, give me some advice what i can do to use this device properly.. every negative review i read about the penimaster is about blister and stuff but noone seems to just slip out..
I used lube but not too much i dont think thats the reason, i Think its my foreskin but there needs to be a way to deal with this..

Anyone?

I have trouble with slippage too and swelling/pain in foreskin area . In my opinion this device cannot be used properly by someone who is uncircumcised. My glans is too big (13 cm soft around )even they say that the pm should accommodate easily even 15 cm glans. My advice is to try and use a cheap Chinese vacuum chamber that you can find on ebay/aliexpres . I use one and I can extend up to 12 hours a day without significant discomfort, but unfortunately did not grow a single mm in almost a year of wearing it on average 8-10 hours a day. I think the tension is not enough to produce any gains or maybe I’m just very unlucky. For past 3 months I also vacuum hang 3 kg daily for 3-4 hours and still no gains .good luck

I have a possible solution. I have been using an extender for over a year now. I am also uncircumcised, have a pretty large gland. I suggest getting a silicone sleeve (ebay is like 3 dollars or something). Also get foam material if your kit didn’t come with any.

I actually do not retract my foreskin at all, I leave it at its natural state. Even if your glands are not prominent, put the silicone sleeve on but make sure that the sleeve sits behind where your glands begin.

Next put the base of the extender on.

Now, add foam around the silicone behind where the glands should be.

Lastly, you have to carefully put the noose or strap that is wrapped in foam behind the glands and tighten it.

You can then lay in the prone with the extender pointed down. This will not slip off. Give it a try. I do this with a warming mat beneath me.

Hi Bomber99!

The “androrings” that I use come with the “Andro Comfort Kit”. pic (andropenis extender)
You can find it on e-bay.
It really help to prevent slippage but, I am circumcised.
I also use sometimes a “cotton tissus” or a “shoe lace” tight enough around my extender under my glans. (link)
Suggestion for guys who are not circumcised…do not retract your penis skin when you install the extender.
DJ

Andropenis - DJ8.jpg

Always retract foreskin. Use the smallest latex parts (green color) and the small split adapter and pull back your foreskin. Fill the glans with blood by clamping your hand on the dick. Suck in the clamped/full glans inside the PMP by first having the ball pressed before you connect it. Keep the clamp and disconnect the ball and press it againnand connect again and suck in as much as you can of glans now disconnect yoir glans should be completely expanded inside and sucked in. Now get an erection to keep the glans filled while extending.

Sounds good, how do i clamp my glans? just with o grip?

Yea clamping your glans means with foreskin pulled back trapping blood inside it so it balloons by using an O grip.

The key for me is pushing my glans while it is clamped and filled with blood inside the vacuum chamber while letting go of the green vacuum ball so that it sucks in. Then I suck it in a second time just to get it conpletely secure this 2nd time the green vacuum ball dont completely fill up and i detach it while it is still compressed.

Are you uncut? I have the same problem. It either slips or doesn’t go all the way in or when it does it pulls in foreskin and ruins it. But other extenders won’t be much better.

If I do this the foreskin will always get sucked in and ruined.

Learn to use it.

I’m hanging 2,5kg at the moment with penimaster.

Blue one is a bit big, but its doable.

Yellow one is best fit for me.

Green one is a bit small, but it streches out and no problem. I’m uncut.

So the process goes like this. Pull back your foreskin and attatch vacuum pump on your device. At the same time hold your foreskin back and press your gland against the entrance hole, release the pressure from the and turn right to unattatch the pump. Now press the pump again in vacuum state and reattatch to devise, release the pressure from the pump slowly until your glands are sucked in as much as it is comfortable to you. Not too much, because it will suck your foreskin in the device allso.

To understand better, take the device in your hand, attatch the pump and release, at the same time look in from the entrance hole, and you can see how it sucks the rubber in, now unattatch the pump and repeat, and the second time look inside from the hole and you can see how it makes more vacuum inside.

The device is amazing, learn to use it properly.

The gland size doesnt matter.

Good luck

I’m 300+ hrs in, by this time I’m pretty sure “i’ve learned to use it”.

That is literally what I did (wha you are describing) and you can see it causes bad issues.

This guide shows you should use glans cap, maybe that would help for me?

Yes I can attest to this. PE isnt free and it not just buying a decive its paying enough attention to learning it properly, it takes a lot of time maybe even 100+ hours with a device before you master it and can get the full effectiveness.

I can pull manually with all my strength when im in the PmP head, thats atleast 20kg of force and it wont slip.

HenrikL, isn’t getting an erection in an extender dangerous ??? I’m not sure I’m understanding the last part.

PMP slippage problem is no fun, but I’ll try the green latex parts instead of the blue ones I tried.

Why would it matter if you get an erection? If you’re already extended, I wouldn’t think it would exert greater pressure. The only issue I could see is if you are using a strap.

Bear in mind that I’m no expert, just on here learning like everyone else. :-)