I'm thinking about pumping for more length...

I’m considering using a pump after hanging weights to try to give me a little more length. I’ve checked into the Boston Pumps & the LapDist ones. Which is better? I like the Boston one with the contoured base, but I’m not sure if this is the one to go with. I only want to add length & not girth, since my girth is already over 7”. What ID cylinder should I use? I’m considering one about 10-12”x2.25”. My cock when hard is about 2.5” across, but I rolled some plastic into a cylinder & 2.25” worked with lots of lube, but was pretty tight. Is this a good thing, if I’m just wanting to add length?

Over time, will it compress my cock to 2.25” wide & make it more rounded? This would be great if it would, since it’s more oval than I’d like now. I’m just about 8”bp right now & just over 7.25” girth. I’d like to get 9” bp if I can, to get a better proportioned unit. Am I on the right track? I haven’t been PE’ing for a little while, so I should be deconditioned now. I think that is one reason that my length gains stopped.

I forgot to say: Thanks in advance for any help. :)

Personally , I think that you should stick with hanging and stretching to work towards length increases .

Pumping tends to develop girth , and from the sound of things , you have that covered , yes ?

So , hanging , stretching , and look into an A.D.S. .

I think the lapdist pump is better. For one thing, the pump is all brass and not plastic like the Boston pump and the lapdist cylinders are very comfortable.

I think your cylinder size should be 10” X 2.5”.

As discussed before here - go to Harbor Freight buy your pump for $15 to $30 (it is the same as the high quality one from LA DIST) and then just buy the tube from them.

I was thinking of using the pump at moderate pressure after hanging, as an ADS. The cylinder would be about the same as my current girth. I could maybe even go with a 2” ID cylinder, but I’m not sure how uncomfortable that would be, or if it’s even possible. I was thinking that I could just use the pump as an ADS to keep my dick extended after hanging. Maybe pump for 30 minutes at a time with just enough pressure to keep me extended just beyond my normal erect length, for a few hours, with 5-10 minute breaks in between…Bad plan?

I considered the 2.5” cylinder, but I was worried that I would gain girth in the process. My cock is about 2.5” across, but it’s kind of oval, otherwise it would probably be about 8” midshaft & I thought that a 2.5” cylinder might cause a gain in girth as well. I definitely don’t want a girth gain, as a gain, any gain, in girth would be bad for me. I was thinking that a 2.25” cylinder might even, over time, change the shape into a more rounded one & possibly slighly less wide. Could this happen? So, you like the LapDist? Also, if I get the pump, what should I do to avoid getting the donut effect toward the end of my dick? I have some Theraband that I use with my hanger. Could I use some of that to wrap the end of my dick, just behind the head? Would this work? I read a thread about condom pumping that seemed interesting, but even Magnum XL’s are VERY difficult for me to use, (They are almost impossible to get on & they strangle me.) so would the pump make it even tighter? Dangerously so? Any help would be grately appreciated. Thanks in advance.

I see… I’ve seen this pump. It’s the one for bleeding brakes, right? I’ll do that… Thanks. :) Everything matches up & works with the cylinders from LapDist without getting an adapter? Also, what’s your opinion on the cylinder size that I need? I don’t want to increase my girth at all, only my length. In your opinion, if I were to get a 2.25” cylinder & use it for several sets of say, 30 minutes, after hanging, would this permanently increase my length over time? I’m wanting to use it just to keep my dick extended after hanging, as an ADS. I’d like to add another 1” of length, if possible. Feasible? What sort of routine would you recommend? What has your experience been with pumping? Have you made permanent gains? If so, how much & how long did it take? Thanks in advance.

I use a Vacutech cylinder thick wall with Mityvac metallic hand pump. The length gains with pumps are probably much less than hanging since I’ve noticed that at the recommended low vacuum hg’s the length is less than what is achieved with higher vacuum.

I think a 2.25” cylinder will be too tight and not allow for easy stretch and expansion. You need some room to allow movement in all directions. It’s hard to predict which direction your gains will go, but a 2.5” cylinder will hopefully be enough to give you only temporary girth enlargement while offering enough freedom for good length expansion. You can’t just stuff your cock into a small cylinder and have all of the pressure just work on the surface of your head. It is easy to develop water blisters on your head this way.

Why the hell am I helping you anyways? You are freaking huge! :)

If you buy a pump from Harbor Freight or an auto parts store, you are going to have find plastic tubing and a male quick disconnect connector that will plug into the female quick disconnect connector on the cylinder. If you are not into the mood to do the plumbing parts roundup, then just buy the lapdist system that is ready to go out of the box.

:) Thanks, but I’d really like some more length to balance it out a bit more. What has your experience been with pumping? Do you pump for girth, length, or both?
Going with the 2.5” cylinder, I’m just worried about getting more girth. I want to only gain length, but I also don’t want any nasty injuries either.

I believe I’ll buy the cylinder & male coupler from La Pump & the pump from Harbour Freight Tools. What are the benefits of the 2-stage cylinder? They say on their website that this is the cylinder that I need to gain length. True? I know that it’s much more expensive, but that’s all that I know about it. Anyone here with experience using a 2-stage cylinder? Will a standard cylinder give me just as good permanent gains?

If anyone in here would like to give me any information on the permanent gains that they’ve made using a penis pump, time frames, routine, etc. I’d be very grateful. Thanks again.

Two Stage? From the description I’m reading that is the cylinder used to pump both your penis and scrotum at the same time, nothing about length? Maybe I missed the link that says where it’s better?

This is on the LapDist website, in the FAQ section:

<How many cylinders should I order?
<We suggest that you order two cylinders: a standard penis cylinder and a 2-stage cylinder. The first or standard cylinder will thicken as well as lengthen the
<penis. The 2-stage cylinder or second cylinder pulls at the suspensory ligaments and adds length.

I’m confused about this as well. How does the 2-stage cylinder focus more on the suspensory ligaments? Is this second cylinder even necessary, or is it just a way for LapDist to make an extra $170? Also, does this cylinder help to make the balls hang a bit lower & stretch the skin between the cock & balls? If so, it might be worth the extra $170, for me at least. I’m considering a foreskin cylinder as well, but I’m not sure how well it actually works. Couldn’t I just rig up the same thing by using some sort of ball & stuffing my standard cylinder a bit? They say on their site that the foreskin cylinder is uncomfortable to use. How uncomfortable are we talking? More uncomfortable than hanging 35-40lbs. with a Captain’s Wench for 3x15min. sets? Thanks again.