Selecting Your Cylinder Size

Thanks for your help gprent!

Got everything together at this point, all for under 70 bucks! Not too shabby.

Had my first run today, 2 5-minute sessions at around 4hg. Already packing out about the first 2.5 inches, can’t wait till the rest of me catches up! (Though of course I’m pacing myself :) . )

Comfortable seal, a very pleasant sensation. As mentioned in another thread the Cowper’s gland certainly goes crazy.

Might need a 2.25 sooner than later.

I’m sure this has been asked before but I am aiming for length am currently at the lower-end of one of the thresholds. I’m 5.50” girth mid-shift and I’m pretty uniform from top to bottom. Even the head is within maybe 0.10”.
1.75” circumference fits up to 5.25” so I think I would say that if I were to purchase that one, I would already be “packing” that one far too much but I’m thinking 2.0 I won’t pack yet so I’ll be gaining girth. I’m confused which one to go for.

Select the 2.0.

I agree 2” is a good choice. However, the LA Pump elongated 1 .75” (1.75 x 2.25) is just slightly larger.

My MSEG is 5.5” and fits nicely into the elongated cylinder, I pack it after 30 minutes at 5 hg.

Hi Guys,

Does cylinder size really matter that much? I have an LA Pump with a gauge its an air pump its 9”x 2.5” I’ve only had it about 2 weeks but I get really good expansion when using it.

The size only matters in terms of getting a proper seal. If you selected a size larger, keep an eye on things. You’ll be more prone to fluid accumulation.

Hi Titleist always good to hear from you.I do get a bit of fluid built up under the glans but that goes away after 2-3 hours.I notice a bit of the fat pad gets sucked into the cylinder not that I have much of one I don’t think thats a problem though?Obviously im new to pumping so not entirely sure.It seems to seal ok I just rub a bit of lube around base of cylinder and it seals fine.

I recently bought my first basic pump and it has a 1.75” cylinder. My EG is 4.75” so logically that should work. However, I have a downward and a left curve. My penis ends up getting sucked up against the cylinder wall. It’s an Utimi with the gauge but I’m not real happy with the bottom sleeve either. I’m thinking of investing in another, maybe a 2” with a more substantially based entry sleeve. Any recommendations or advice?

1.75” cylinder will fit you well and to pack this tube we are talking about 5.5” EG. 2.00” cylinder will be too large and might be end sucking your balls (very uncomfortable, should be avoided).

Make sure the entire cylinder is lubed inside, so your penis could “slide” on the walls without any problems.

My situation was the same as yours: back few months, was 4.7” EG with a downward bend (midshaft). At 4.9” EG now, still comfortable on 1.75” … long way before start using the 2.00”.

Thank you Useful!
Er, Useless. That just doesn’t seem like the appropriate name given that you have just helped me out lol.

What’s funny is I did just that yesterday and it does seem to work. I was able to pump up to about a 1/4in longer with it being able to slide inside better.

Woo-hoo!

I also feel like doing the hot tub first with some light stretching and jelqing is helping as well.

Then I do the pump at 5hg for 10 to 15 mins, back to the hot tub for 5 mins before using my sizedoctor vacuum extender for 2 30 min sessions and finish on the hot tub with massage and more light stretching and jelqing.

I noticed yesterday that I am at 7in while on the extender so that’s a good sign !

Starting BPEL 6.25

Nice to hear that.

I don’t get it.

Hey there,

I just wanted to chime in and say thanks again for the size recommendations. I got my pump today. It took me nearly a month as it sat there forever in customs.but.it finally arrived :) First thing I did was get nice and erect and then test it out. Fits with just a very reasonable bit of room pre-pumping which is perfect for my goals of length gains over thickness gains. I have no doubts with a full erection plus two or three minutes of pumping, I’ll be filling the tube pretty well.

It might take a bit to do that though.. I can’t seem to get any pressure in the tube so I think I’m doing something wrong. I’m just not sure what. With my old pump, the pump was part of the cylinder and directly attached. This one, I have to attach the tube and then pump it seems. I recall somewhere in one of the pages, someone mentioned having to .press down the quick release value or make sure it’s not pressed or something with LA Pump Pumps..

Any advice for a newbie with this pump but not a newbie to pumping in general?

Thanks :)

My situation involves finding a cylinder that has a greater maximum insertable length. My E.L. is breaking 9” and I am bottoming out my head against the end of the cylinder. I need one that is longer but I don’t need one that’ 12” I need one that’s 10” insertable.

In my searches, most pumps are too short and are therefore useless to me.

Is there a site that reviews all the pumps and cylinders out there specifying max insertable length?

Here you go: