Should I buy a bigger pump than I need to save money in the future?

Well my girth is 4.8in and I would fit into a 9x2 pump but a 9x2 pump only fits a girth size of 5.5in whereas a 9x2.5in pump fits past 6in girth. Wouldn’t it save me more money in the long run just to get bigger 9x2.5in pump? Or is it important to get a pump that is closer to your size?

I only ask as over time I will out grow that 9x2 pump.

With that said the pump I am purchasing is the LeLuv 9x2 pump but I am tempted to buy the 9x2.5 pump I’m just hoping someone can tell me why or why I shouldn’t just get the bigger pump. I would consider myself a begiinner.

Actually the best size cylinder for you is a 1.75" diameter. Here is our sizing table:

Selecting Your Cylinder Size

A 2" tube would be too large and you would have trouble with your scrotum and balls being sucked into tube. A 2.5" tube would be big enough to pump your entire package, cock and balls.

This is a very good question. I thought the same thing a while back and bought an oversized cylinder. But it really doesn’t work that way. You have to precisely size the pump, per gprent’s recommendation, above.

Are you 4.8in at the base or more? I’m 5 inches mid shaft but I can pack a 2” in tube at the base without issues.

I would go with a 3.5 or larger and do the whole package…

DiamondHusky, friend you think your 12,2cm girth dick will fit in a 16,05cm girth cylinder? Think twice, your girth does not fit into 2” diameter cylinder because there is your penis and there is skin, the pressure will expand both, it is obvious that the lack of meat you have will make your pubic skin being the one pushed and expanded the most, that means no dick gains, best option for you is 1.75” diameter. If you buy the 2.5” diameter cylinder, that means 20,06cm girth, you better put your whole package and yet you will gain lots of skin.

I’ve been using a 1.75” cylinder since I began pumping seven years ago. I did have a larger cylinder as I could not go smaller with the Bathmate, as gprent pointed out, my balls would get sucked up quite often.

My girth has increases from 4.50” to 5.00” and the 1.75” cylinder is still right for me. To pack a 2.00” cylinder I would have to take on more edema than I would prefer.

My recommendation is as others have stated, size for where you are now.

Thank you I will listen to your advice and the advice of others in this thread and get the 1.75!

I have a cheap pump that is something like 2.75 I think? It’s been a NIGHTMARE. Sometimes I have great pump sessions and other times after 15 mins my balls get sucked into the tube and it hurts.

I am 4.7 at the base and 4.8 midshaft I’m not sure if that’s normal to be thicker midshaft than the base but that is the case for me

Thanks for the advice is there any benefits to doing the whole package?

Thank you c3ifador for breaking the numbers down to me like that. You’re right. I am going to get the 1.75

Thanks LittleEngine. I’m glad to hear that the consensus is for me to get the 1.75 that feels like the right decision now and since you are where I want to be both length and girth wise I think it’s best I also listen to your experience and follow the same advice you’ve given.

I can tell you that even the pressure on the penis feels different and I jumped only from 2” to 2.25” [Its a little bit big for me]

I agree he needs the 1.75. It’s best to use the size closest to your size until you actually out grow it and then you move up one size at a time. You’ll be wasting money if you go to big.

While I have been a full package pumper, I have been taking a break and experimenting with cock tubes. I picked up a 2” cylinder locally and used it a few weeks. Nice, but wasn’t really doing anything as I was unable to pack it no matter how long I pumped.

I ordered a 1.75” and have had it about a week now and it was well worth it. I am thinking of looking for a 1 and 7/8ths tube to go between the two…

I am packing the tube and seeing length expansion that I wasn’t with either the full package tube or the 2” tube.