Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Size of cylinder

Size of cylinder

In a few days i’ll make a homemade vacuum and post the how-to in the spanish forum…

But I have some doubts… What size of cylinder i have to buy for center my gains in lenght? and what for increase in glans size?

Now I’m 6,8” bp x 4,8”


CURRENT 7.1" x 5" (8" stretched) ----> GOAL 8" x 6" NBP

Semen retentum venenum est

A cylinder with an ID of 1.75” should handle both your length and girth requirements. If you could, a 1.6 inch cylinder might be a better fit to go for length, but not sure if you can buy that size. 1.6 X 3.14159=5.0 girth. If you get a cylinder too large in relation to your girth, you will have a hard time keeping your balls from being sucked in the cylinder.


The primary goal of PE should be to make your penis as healthy as possible in both form and function. If you do that, increased size will follow.

Thanks gprent101! I think the 1.6” tube I will crash it with my base or glans. I think it’s not for me:D

I’ll go to a shop where sell meth-acrylate tubes. So I’ll look for the 45 mm diameter one (1.77”) If don’t have it I’ll have no option and buy the 50 mm one (1.97”). Another option it’s buy all (1.6”, 1.77” and 1.97”) and make some benchmarks….:)

And what about the long of the tube? How many inches long I have to take it? (3 or 4 inches more?)

Thanks again


CURRENT 7.1" x 5" (8" stretched) ----> GOAL 8" x 6" NBP

Semen retentum venenum est

Your length is now 6.3? A 9 inch tube should be plenty.


The primary goal of PE should be to make your penis as healthy as possible in both form and function. If you do that, increased size will follow.

NBP yes. BP it’s nearly 7” (6.8 or 6.9). OK


CURRENT 7.1" x 5" (8" stretched) ----> GOAL 8" x 6" NBP

Semen retentum venenum est

Yes, OK. Now pack it.


The primary goal of PE should be to make your penis as healthy as possible in both form and function. If you do that, increased size will follow.

I was reading the 8th page of the sticky post “Vacuum Pumping 101” when I found in avocet8 words:

“To all of you - newbies should always buy 10” cylinders at least. Give yourself some length room. They don’t cost any more than 8” cylinders from most manufacturers.”

Now i’m confused, gprent101,

I think I’ll take it of 9 inches, but what will be the differences for my lengths purposes between one of 10” and the other of 9” ?


CURRENT 7.1" x 5" (8" stretched) ----> GOAL 8" x 6" NBP

Semen retentum venenum est

Guess it just depends on how optomistic you are!


The primary goal of PE should be to make your penis as healthy as possible in both form and function. If you do that, increased size will follow.

Quote
Originally posted by mescalino

“To all of you - newbies should always buy 10” cylinders at least. Give yourself some length room. They don't cost any more than 8” cylinders from most manufacturers.”

Now i'm confused, gprent101,

I think I'll take it of 9 inches, but what will be the differences for my lengths purposes between one of 10” and the other of 9” ?

Point is, extra height in a tube will not change your pressure values within it, so a longer tube is not a disadvantage. Further, if you do get to 8 inches L under pumped pressure, your glans is going begin to be smooshed up against the valve that pokes down at the top of the tube. That is very uncomfortable and can cause bruising or damage. A 10 L tube costs no more and gives you plenty of leeway.


_______________

avocet8

I’m making my cylinder! In the shop have 2 diameters for my size 1.65” and 1.75”. I take the 1.75” one and i’m cutting it now! I’ll cut it at 10” length… :) i hope i’ll do some lengths gains with it…


CURRENT 7.1" x 5" (8" stretched) ----> GOAL 8" x 6" NBP

Semen retentum venenum est


Last edited by mescalino : 02-03-2004 at .

Tube length and diameter

I am new here but I have had great gains combining exercise and overall fitness and bodybuilding and surfing with the exercises. I am totally committed now to pumping and leaving the tube on .
I have 7 girth (circumference) and about 9.5 length ,. I had avoided the thicker tubes as the entrance size (inset) was critical so the tubes would not suck in the balls. Even though I have giant balls I still had issues . So I had my pump company man make me another big diameter tube ( 7.5 inch circumference) and he made it longer than I needed ( 11inch) and made the tube 13 inch .I thought it would be way too big but it feels great and is rapidly filling .he made a special double thick silicon insert ring that spreads out the pressure across a bigger area and he angled the tube and it is fantastic!~.. I prefer pumps and then leaving the tube on and have had enormous gains that way . A lot of the reason I am into increasing size and pump is to increase testosterone release that I use for bodybuilding and sports drive.. Being horny when you lift or exercise can really increase your gains in both areas.

I am positioned on pumps and the right tube designs to get great results with less effort and time..
Anyone else out there an expert in tubes / techniques that might have something I can add?

Other wise I get really excellent results with pump/ tube

Found that holding off a day or two or overnight can allow the Dick to get back to right proportions and natural length .

You already have a cylinder custom made to your requirements, but just for info, here is the chart we use to determine optimum cylinder size:

Selecting Your Cylinder Size


The primary goal of PE should be to make your penis as healthy as possible in both form and function. If you do that, increased size will follow.

Top
Similar Threads 
ThreadStarterForumRepliesLast Post
Pumping Question re cylinder size and packingmugglesPenis Pumps1107-21-2008 11:33 PM
Finding a different size homemade cylinder?Josh 14-11Penis Pumps1006-18-2008 12:27 AM
condom/water pumping cylinder sizedreamaloud1Penis Pumps103-12-2007 02:53 AM
Cylinder size selection questiona529612Penis Pumps208-22-2003 04:27 PM

All times are GMT. The time now is 10:38 PM.