The SuckXtender - just remember it sucks!

This is the same concept as the ventless TLC Tugger except the forskin is not used, so the skin doesn’t get stretched. Very interesting! The TLC Tugger pulled on the end of the glans, does this do the exact same thing?

Can the condom last for hours so we can wear it as an ADS?

The end plate is a piece of mild steel sheet cut to a shape as shown. It has two 5mm holes drilled in it to take the rods and I welded a pipe support bracket (the type plumbers use) to the back of it so there was something handy to pull on (or hang weights from if using the attachment for hanging).

Yes, effectively the stretch goes onto the glans and the internal penis.

So far I’ve only been using the attachment to hang light weight (<6lb) and its very comfy for an hour+ at a time - I don’t see why the stretcher should be any different. The condom will maintain a seal for hours but ideally a better rubber/silicone sleeve or tube will be found which will be more durable - the condom wears out after being used several times.

How did you attach the vacuum device to the mild steel sheet? What’s that white stuff?

Have you logged any hours with it yet?

In the pictures the end plate is stuck to the vacuum chamber with a bit of blue-tac. I have since used epoxy resin glue to stick them together.

Will start trying out the suckX tomorrow. If all goes well I’m planning a routine repeated morning and evening as follows-

10-15min Hot water warm up and manual exercises, including manual clamping. Followed by 30min-45min in the stretcher set at an initial tension of 2-3kg.

Between routines I’ll wear a 1.5lb golf weight and elasticated bandage wrap.

I’m looking forward to seeing if the “static” stretching at a fixed extension and allowing the stress to relax over time will produce any better results than hanging, which of course maintains a fixed stress.

mbuc,

How will you judge tension, by feel or have you figured out yet another elegant solution?

We’re rooting for you!

I think, once I’ve got the suckX on, I’ll probably hook a couple of kg weights on a cord and hang them from the end plate, then push the base plate hard against my pubic bone and tighten up the bolts, then remove the weight. That’s the plan anyway - experience will prove whether that’s workable but I think it should be.

Have just tried out the suckXtender for the first time. And boy -
THIS BABY SUCKS!

I wore it for half an hour this morning and it wasn’t comfortable to wear - IT WAS POSITIVELY PLEASURABLE! (sorry for sounding like an over enthusiastic salesman here but I was surprised how well it worked)

I’ve posted some pics of it in use in the members’ picture forum here Stretcher Pictures

Whew! Good to hear!

I was thinking about the best method for anybody to make one of these stretchers without having to do any welding.

The 5mm screwed rod usually comes in roughly metre lengths. To make the stretcher rods without welding I would measure the required length of rod (I used 8”) and put the rod in a vice so the 8” mark is level with the top of the vice. The rod can then be bent fairly easily by hand to a 90’ angle. Then take the rod out of the vice and saw the rod so as to leave just enough ( 7or 8mm maybe) at right angles to go thro’ the base ring with a few threads exposed on the inside to fit a thin washer and nut. Repeat the process to make the other stretcher rod. Once assembled the nuts could be fixed with a drop of superglue to stop them working loose.

I’ve just finished the first week of using the suckXtender. The measured BPFSL measurements before and after each session very not very exciting - each time they were about 6.9”before and 7.0”after. I’ll post a weekly update here in the following format.

Week 1

…………..Hours”up” Hours”down” Total hours BPFSL Before After

Week 1……..4…………….7……………11…… …….6.9”……7.0”

A ‘not very exciting’ thread is probably far more valuable than a ‘mega gains’ thread, as it shows what would really happen for the average joe which by definition most of us are. I would very much appreciate your weekly update.

For various reasons the last week has seen me do less PE than anytime in the last year. I only managed to use the suckX on 2 days. However, I hope to get some serious hours in this coming week.

Week 2

…………..Hrs “up” Hrs”down” Weekly Hrs Cumulative Hrs BPFSL Before After

Week 1……..4……….7…………11…………… 11………………..6.9”……7.0”
Week 2……..4……….0………….4…………… .15………………..6.9…….7.0

Yippee! A 0.1” FSL increase this week.

Week 3

…………..Hrs “up” Hrs”down” Weekly Hrs Cumulative Hrs BPFSL Before After

Week 1……..4……….7…………11…………… 11………………..6.9”……7.0”
Week 2……..4……….0………….4…………… ..15………………..6.9”……7.0”
Week 3…….11………7………….18…………… .33………………..7.0”……7.1”

Let me be the first to congratulate!

:up: