Discoloration from Hanging

This is a problem I too encountered with the Bib. It is a “hard” hanger and I like to hang with as little wrap as possible. The tighter I would make it the more I bruised. This bruising increased proportionally to the weight I would use - more weight/tighter hanger = more bruising. This was a bummer because I like the Bib Starter - it is a fantastic device.

Like I said before: The only effective way around this was to use less weight and more sets. I could ease the bruising a bit by adding layers of wrap, but this brought with it other complications, such as internal twisting and head bloating/strangulation - it really became quite a balancing act.

In the end, the Wench worked better for me. Minimal amount of wrap and I never bruised with the Wench.

Uh, I didn’t drink that much last night.

I don’t remember this thread, let alone starting this thread…

Uh, I didn't drink that much last night.
I don't remember this thread, let alone starting this thread…

Ulcaster, maybe you should stop the sign of the first empty bottle then? Hobby split the thread with a surgical precision (which is odd considering so many threads that get hi-jacked.) :)

Ulcaster do you do the jelqing in between the sets? I am just curious if at some point your penis is just being worked too hard and that is why you are bruising. Although Cap could be right and it could be a wrap issue. It seems like 99% of hanging is wrapping. Have you tried to use more/less wrap?

goodhead, it took about 7 months to move up 9 lbs but I am using a bookcase to hang over which is probably taking most of the weight. I have no doubt I could not hang more than half that SD with my poor ligs.

Andrew/Mr. Hobby, I think I have heard this discussed before. Maybe I was lucky enough not to have problems because of the relatively low pressure so far transferred to the head. The only problem is that if you keep the end near the glans filled with blood so the hanger doesn’t slide how does the blood not get pushed into the head anyway?

And Andrew let’s watch the “pin dick” comments, or I am going to start calling you “trouser tadpole.” ;)

-Tom “Zombies ate my brains!” Foolery

Run it down for us again.

1. What position are you currently hanging?

2. What is the weight?

3. What is the amount of space between the hex nuts and the plastic?

4. Do the teeth mesh when you tighten?

5. Describe your wrap?

6. Describe how you wrap?

7. How many sets do you day per day?

8. How long are your sets?

9. And the big question, (Tom “Speedy Gonzales” Foolery” had just asked you in the above post) are you doing jelq in between sets?
Before hanging?
After hanging?
IOW - What other PE are you doing in conjunction with hanging?

The darkening is mostly on the underside of the shaft, infront of the hanger.

The color is dark purple to black. No brown. The color is solid, not splotchy.
It’s clearing up slowly……..real slowly.

A good idea, my dick is too small to use a fulcrum device with my hanger…..at this time.

I do a couple light jelgs and leg slaps, then apply heat till the next set.

I does seem like hanging is 99% wraping…….and placement.

I have tried more and less thera-band. I’m looking for a new kind of material.

Over the shoulder at ~80 degrees.

10lbs. Dropped to 5.

1 1/2 centimeters.

Yes

Thera-band. About 2 feet.

Fairy tight, width of about 3 inches ( BIB width)

Atleast 4 sets, average of ~8. I could’nt break 2 hours, hang time.

15-20 minutes or till cold

I jelg, leg slap, and heating pad between hang sets

Other PE
Pumping, clamp, power jelq, ADS (JES) . I basiclly do it all…..

Similar to this? If so, another cause not mentioned in that thread is the wrap being too tight or inelastic, especially nearest the head. Any non-stretchy underwrap must be applied loosely. You said you’re using about 24” of Thera. I assume you’re spiraling. Be careful not to build up too many layers toward the leading edge. If you do it can’t stretch.

In that example the hanger is adjusted incorrectly. The bottom needs to be wider so the top teeth are closer together after final tightening.

Another problem in those pics is the hanger is positioned too far back from the leading edge of the wrap. Anywhere from almost even with the edge to about 1/4” behind it works best for me.

The CS (bottom chamber which becomes the head) doesn’t share blood with the CC’s. Vessels run between the CC’s, allowing blood exchange between them. Caverject can be injected into only one CC, yet both become erect. The CS is a separate entity with its own blood supply.

My suggestions:

Change positions. Go to SD or BTC. You are more prone to bruising at OTS.
I don’t think OTS is all that great, but that’s only my opinion.

Test: You should be able to piss while the wrap is on. If not, the wrap is too tight.

A plumped dick is not suitable for hanging. You want that thing to be a skinny, limp noodle.
And don’t look at porn while hanging! It will have an effect.

I really think you should concentrate on hanging, and then do the other stuff when your hanging phase is over.
Max out your ligs with BTC now, and then move on to other stuff.

Very similar, but the brusing stops right at the circ scar.

I will check the settings…..

The teeth come together fine, I’ll play around with a new fit.

I get the bruising from all angles so far, but OTS is the worst for discoloration.

Check

I always hang first. Hanging after a pump is painfull.

UD,

Basically, all you need is an inch or so between your body and the hanger. If you can manage that, I think you may be able to use a fulcrum.

I also agree with Ramrod, you are just doing too much and your dick is simply not getting a chance to heal. Concentrate on one thing at a time and I’m sure you will be better off.

Hey UD,

Your pics are here.