Experienced uncut hangers

I’m uncut and have been hanging for long periods (up to 2 hours a day) using a silicon sleeve which applies force to the glans only. I must confess, with weight over roughly 3lb it starts to slip. I’ve been considering the possibility of wrapping just behind my glans over the silicon sleeve to allow for more weight to be added without slippage.

The silicon sleeve I use is one of the standard ADS types, with the leg harness. I clip the connector together to form a loop. Then I put a clamp through the loop, then I attach the clamp to a vitamin tub (long vitamin C type from tesco)

I put random weighted objects inside the container (heavy duty bolts etc that i’ve weighed) until i’ve achieved the desired weight.

This can cost as little as £8 to setup. Sounds crude I know but hey, it works.

I think having the force bypass external skin-tissue is key. If you stretch your unit with your hand, holding the foreskin, then poke a finger into the deep tissue of your unit, you’ll notice a significant lack of tension (I do)

If you however grab the glans and pull, and poke the internal tissues, you’ll notice it’s very taut in comparison.

My two cents.

Uncut with a Bib hanger

I’ve just started hanging again recently, so I’m only hanging 3kg. At this weight I’m wrapping with 45cm of very thin bandage. I hold my glans, and stretch out my penis. I then run a finger down the underside, so that loose skin gathers at the scrotum. I then wrap down and then up. I start about 1cm behind the edge of the foreskin (wrap will ride forward slightly during hanger attachment), and I attach hanger 1 cm behind this.

At higher weights I use less bandage with an over layer of an ace type bandage. I’m not a fan of theraband.

I agree with Audacia, in that advice for the cut does not work for the uncut, and most of the advice out there is for the cut. I’ve had to experiment, and sometimes what worked for one week doesnt work for another. All I can say is that the Bib is very flexible, so get yourself an array of wrapping materials and just take sometime to experiment.

With a padded Bib you may need less wrap than you think.

Currently I pull the foreskin back, stretch my dick out and wrap far enough back so that when the foreskin moves forward the wrap is directly behind the glans. Since I have such little shaft skin I’m attaching the hanger just a little behind the head, I then tighten up with quite a bit, squeezing out blood making sure my shaft is in the correct place, when it gets a little tight I move it forward to a more comfortable position, by this point is literally right behind the glans.

I’ve just moved up to 8lbs and it’s quite comfortable. I am worried about using higher weight with the hanger so close behind the head, sometimes if I don’t tighten enough it can slip causing the head to tilt to the right.

Also I’ve noticed depending on how I’ve lined up the head, it will normally want to go to the right, which will cause the outer penis to want to lean over the inner penis to the right. So sometimes you have to compensate by titling the penis head left in the hanger some sets.

Looking at the Bib, the last ridge is inclined helping to form a plug which the foreskin should help. I try to make sure that there is wrap visible above the well of the hanger (I also have foreskin outide the wrap) , if you measure the highest point of that last ridge it is about an inch back from the top of the well padding.

If you need to move the Bib, I would move back rather than forward. I’m sure that there are hanging threads which discuss the need to vary the attachment point at times due to a level of discomfort, and the general concenus has been to move back for a couple of sessions (I will do a search and see if I can find them).

Maybe there is a need for a discussion around whether being uncut provides you with a bit more padding in the glans region. The Bib ensures that we dont put pressure onto the nerve plexus on the shaft beneath the glans, but you still do not want to put the weight right onto the coronal ridge

Do any of you guys happen to use an ADS at all?

Uncut here, been hanging with the bib for quite a while (originally used a sock hanger years ago). One thing that works for me, is to re-wrap between sets. I know Bib says not to, but I see towards the end of each set, the foreskin around the glan does swell a bit, nothing serious nor dangerous. Re-wrapping between sets helps bring that swelling back to normal, with just light jelqing.

I do as well.

By the way, I do not stretch before hanging because that’ll make my penis too long. I find that if my penis is too long while I hang bad things happen; ie. half my penis is hanging off the end losing circulation and whatnot.

Oh and in addition to my question on whether any of you uncut guys use an ADS, are any of you guys hanging over the shoulder with the penis up, or to the side etc, because of a certain LOT?

answered here
and here

I hang OTS to target the tunica, I personally do not want to overstretch my ligaments.

I used to hang OTS, but stopped because I didn’t find that it was helping.

Today I hung with my penis being too long and got many burst capillaries. That’s how it goes.

Thanks for posting stuzilla - hopefully when I get my Credit Card working I can order an ADS and hopefully they work for us uncut guys.

I’ll probably order a bib starter as well

ADS works fine for uncut guys. I used to wear one all the time. If your foreskin is stuck over your head, that might be a problem. But mine easily goes back.

I have been trying to use the BIB Hanger the last couple days but once I wrap and put on the BIB it always falls off and slips. I am considering circumcision. The ADS these guys are talking about are called Xsleeves, I had one and did not really think it was doing anything. It’s not a real ADS that cut guy’s use that gives real stretch like an extender or something.

Have you played with the adjustment nuts at the bottom?