twisting revelation***need help

Ok guys, If any of you had read my last post (Help, confused w/ many probs) you know I have a wicked twisting problem. Well I have done some experimenting (w/ settings and wrap) and still have yet to solve it.
I have found out that if I am hanging straight down—-standing up and leaned over slightly, hands resting on table—- I hang straight as an arrow. When I sit back down, it immediately wants to go 90 degrees, predominantly to the left. I think it is something w/ my CC, maybe the shape of it.? I’m thinking that it is when my penis is obstructed or slightly resting on something (like my pelvis bone) the shape of my CC is causing my penis to roll in that direction. My CC doesn’t seem oval, but maybe it is slightly. When I shift it from 90 degrees to say 20 on the opposite side, I can definitely feel the meat of my shaft (my CC) shift.
This is my best guess. Now as to how to fix this, I’m clueless. It is driving me up the wall.
——bigger, could I sustain injury if I just said screw it and let myself hang 90 degrees while sitting? Have you heard of this kind of thing?

Guys any help/advice you could give would be greatly aprreciated. This is very frusturating and discouraging

Jake,

>bigger, could I sustain injury if I just said screw it and let myself hang 90 degrees while sitting? Have you heard of this kind of thing?<

If you are writing of your entire shaft turning 90 degrees, safety is not a big issue. If you mean your head only is turning 90 degrees, then that is a problem. You could be putting pressure on the nerve bundle behind the head.

The few times when I hung standing up or walking, my entire unit would turn to one side or the other. But the vast majority of the time, I hung while seated.

If the entire shaft is turning, the easiest way to solve it, if you wish, is to use the skids on the bottom of the hanger to press against the chair, assuming you are using a Bib. I made an extension out of a split piece of 4 inch PVC pipe, to go over the front edge of my chair. Then, I would put a smaller diameter pipe within the larger pipe to get, in effect, a longer chair seat. The skids of the hanger would ride on the pipe, whether I was hanging SO, BTC, or any angle in between.

Bigger

Jake,

If you are twisting within the hanger, you may simply not be tightening enough. If you are straight when you attach the hanger, and then it twists when you apply the weight, this is probably the case.

Bigger

Ok, so if the entire shaft is twisting 90 degrees, with the unit, this is normal and has happend to you? Ok that is re assuring. I am no longer twisting w/ in the hanger. I tighten, pull, tighten, pull, then tighten. I found out before when I tightened once it wasnt enough and I would twist immediately inside the hanger when weight was applied. Now I’m always straight, even after hanging; Just the damn thing is always twisting left or right on me, I was worried If I didn’t straighten then my dick might start to curve one way. That would suck. So i’ve been kind of paranoid about this—-constantly holding the hanger/straightening. So this has happend to you? You just driil some halfed pvc pipe to a chair? Hmmm interesting. Although the main chair I use is a padded leather office chair and I really don’t have any wood to drill into, maybe an adhesive might work…

jake,

>Ok, so if the entire shaft is twisting 90 degrees, with the unit, this is normal and has happend to you?<

Sure. It is doubtful that many guys are perfectly binomially symetrical. One set of structures are liable to be stronger on one side than the other.

>Just the damn thing is always twisting left or right on me, I was worried If I didn’t straighten then my dick might start to curve one way. That would suck. So i’ve been kind of paranoid about this—-constantly holding the hanger/straightening.<

If you don’t want to hang with the skids resting on something, just hang on one side for one set, then the other side for the next set. Doubtful that the entire unit twisting would cause any curve because the tunica is not being stressed much more on either side. Just the supporting structures.

>So this has happend to you?<

Yes, before I came up with the PVC extension thing, I would almost always twist while hanging BTC.

>You just driil some halfed pvc pipe to a chair? Hmmm interesting. Although the main chair I use is a padded leather office chair and I really don’t have any wood to drill into, maybe an adhesive might work…<

No. I split about twelve inches of 4 inch ID PVC pipe. Actually, I just cut out the portion that would make it slide easily over the front edge of my chair. I also hung in a padded leather office chair. Then, I drilled a hole in each corner, and tied a cord from those holes to the back supports of the chair. Then, I would put a whole piece of 2 inch, or 3 inch pvc pipe within the split 4 inch pipe to extend further as I grew.

Any questions, just ask.

Bigger

Ok, I think I get it. Besides where the string went. Did you have 2 peices of cord going around the perimeter of the chair that met around the back or were they actually over lapping the chair—-where u would be sitting on them. I don’t think it would make too much sense to have them overlapping but i’m not sure how good it would hold if it was simply tight around the perimeter of the seat… Sorry for so many questions, i’m spatially/mechanicly retarded, lol. Thanks for all of your help man, you don’t know how much I appreciate it! It’s relieving to know I’m doing things right

jake,

>Did you have 2 peices of cord going around the perimeter of the chair that met around the back or were they actually over lapping the chair—-where u would be sitting on them.<

I was sitting on the string.

Bigger