Expansion with low pressure

Recently I bought myself a new pump with gauge and a comfortable silicon sleeve as a seal. I was really surprised to find out how light 5Hg felt on my unit, and when I pumped up to how it usually feels when I pump, I could read almost 10Hg. I then realized that I have been pumping with way to much pressure, and have probably wasted a lot of time.

In the last week I have only been in the range of 3-6 Hg/inch and that feels fine, but I don’t seem to get an expansion bigger then my normal erection, at least not in the length direction. My girth seems to expand a bit.

I wonder if some of the more experienced pumpers can tell me if this is the way to go, or if I should use higher pressure? I don’t get any fluid buildup or red spots at this pressure, and my flaccid hangs better the hole day, but can I expect any erect gains without any noticeable expansion?

I take 3 10-12mins sets with jelq/massage in between once a day. I pump slowly up to 5-6 Hg at each set. I always try to enter the tube as erected as I can. Is that important?

I need some advice from those with success in low pressure pumping?

GarryGirth

Use more time, not more pressure. Just for the hell of it, do 3, 20 minute sets at only 4”hg. I think the results will amaze you.

Also, if you can find an electric heat pad to wrap around the cylinder while you pump, that helps a lot.

Low pressure is the way to go. I personally stay right around 4-5hg and nothing more. I have made some pretty significant length gains from pumping in a very short time that are definitely permanent. From my own experience I have found that less is more with pumping and most PE. If I were you I would experiment with some different routines, more rest time and see what happens. This is basically what my pumping routine consists of…

1. 3-5 minutes of hot soaks (put my cock into a cup of hot water)
2. 3-4 minutes of light stretches
3. pump @ 4-5hg for 15 minutes (I always enter the pump flacid, maybe this helps produce more growth, more expansion?)
4. roughly 50 wet jelq strokes
5. repeat steps 3 & 4 for 1 hr

My best gains have come from plenty of rest. I may pump 1 day on and 2 days off or 2 days on and maybe 2-3 off. Take a look at my 4 month growth comparison pictures to see the results from pumping with this exact routine. Its worked well for me.

thanks, I’ll keep going with low pressure then, and get me some kind of heating pad.

Biggerjohnson well done on the massive gains that you have made that is some outstanding work.I am not going to start a new thread for my question as I think it is applicable to that which is being discussed in this thread.Although since I started pumping I think I have seen some reasonable gains, I think I was around 6.7” before I started and now I am around 7.3”. I too have the same problem where I noticed very little expansion relative to what others have shared or that which I have seen while in the tube and upon coming out; however in the beginning I still did notice some gains despite this factor. I might just give gprent’s shock treatment I shot and see what unfolds. Biggerjohnson, I always try enter erect and at times I have not pumped when I could not get erect( or as erect as I wanted to be) however I think I have begun entering into a phase where I warm up well and pump regardless of my erection degree or status.However if you still managed to pull out some decent gains while entering flaccid then it may be worth a try to continue my sessions even when flat.

Thanks man, its been amazing to see the difference in such a short time.

When I come out of the pump after the very last set Im about 1/4” thicker than I normally am fully hard and my erection level is roughly 70% at this time. I havent been doing this long enough to understand the reasoning behind it but many clampers believe that you get more expansion when clamping/pumping with less 100% erection. I will admit it can take a little bit longer to pump up to a full erection when I enter flacid and you have to play with the pressure, milk the tube, and kegel but overall its worked very well for me and the pictures prove it. I also contribute alot of the growth to my off days with plenty of rest in between.

WOW!!!

Did an hour of heated pumping last night, and the girth expansion was just mad!

Took three 20 min sets with some stroking/jelqing in between, had a heating bottle with very hot water in it, which I used for heating. Entered the cylinder with max erection, and cycled between 3-5Hg.

When I pulled it out, it was hanging fat and heavy as I have never seen before. There were no fluid build up and it lasted the hole evening.

If this is the standard with heat pumping, I think I’ll get some amazing girth results.

Sounds great man. I have a heating pad here but have never thought about wrapping my cylinder with it. Guess I’ll have to give it a shot sometime.

Does anyone has picture’s, or a link to a heat pad?

I found this one out of many, seems like the optimal pad with target temperature regulation:

http://www.cszm edical.com/prod … eat/temppad.htm

but maybe a bit overkill?

I can’t seem to find an electric one with a practical size.
Does anyone know about any good products?

Until I find one, I’ll continue to use a simple heat bottle. Seems to do the trick all though I can’t target the hole surface at the same time.

http://www.walg reens.com/store … jump&navCount=0

Check out the " Muff Style " on page 2 .

Looks like it was made to wrap a cylinder !

This is the heating pad I have used for years. You can find it in Target for around 12 bucks. http://www.kaz. com/kaz/store/p … 9aa79e4aa2c1c0/ If you keep the heat setting one click below high, the pad will last much much longer and still provide plenty of heat.

Thanks, this is much more practical than the ir lamp.

Thanks MB

That’s what I’m looking for, but 17” is bit to long.
At least for now anyway…

I believe 17” is the length for rolling up. 8” is the axial length of the rolled up wrap. But still, it is a bit more expensive then the basic 12”X14” pad.