Help with cylinder size.

Hello guys!

As you know, I’ve been way of PE for a couple of weeks, so I sort of shrinked a little bit. My lenght is now 5.6 BPEL, and my girth is 4.7.

Anyway, I need some help here with the cylinder size (LAPdist) that I’m about to buy (as well as the pump, of course). Anyone?

I know I can check that on their website, but it’s a little bit confusing, and since you’re the vets, you can give me a more detailed opinion!

Thanks my friends!

Big hug

You should buy an 8”X1.75” or if you like, a 9”X1.75”

I know this will sound so so so stupid, but since I still can’t understand the “inches” thing I will ask it anyway…

1 1/2” or 1 3/4” ?

(good old cms… LOL)

And about the lenght… what do you recommend? Will it make much difference? I’ve heard of guys who prefer the 8” cylinder… And I don’t think I will be 9” soon… :D

P.S.: And I only ask this because on lapdist website, they tell you that:

4 3/4” girth = 1 1/2” cylinder
5 1/2” girth = 1 3/4” cylinder

…but I still prefer your recomendations, of course!

1 3/4”

G is the master sizer. Would have saved me buying another tube had I known back then to ask. Don’t pay much attention to the website, they seem to go small so they can sell you another tube soon. I don’t care for too long a tube, just takes more squeezes of the pump. A couple inches over maximum erect length seems plenty.

tps gave you the right size, but I will teach you to fish (math). To get the decimal equivalent just take the fraction 3/4 and divide the 3 by the 4 and you get .75. It is as simple as that. :)

Well, maths is not my strongest area, but I realised that later, it’s the inches that makes me confuse! lol I’m sorry guys, you must think I’m a damn fool by now! lol

Ok… 1 3/4” for girth… and now, for lenght? 8” or 9” ? Does it make a lot of difference?

P.S.: Forget about my stupid question, I just read what you guys said!!! Sorry! :D :D :D (I must be sleeping…)

Good for you. I was about to blast you. :D

:D :D :D thanks! ;)

P.S.: Let me just add, that my doubt was about the effectivity of using a cylinder of 9”, since I’m not even 6” BPEL. I know I could use it, my doubt was if the 8” would be better for me at this point. ;) don’t get me wrong! :D

Get one that is no more than 1/4” larger than your erect girth. As far as the length, that really doesn’t matter.

loki2,

I have a 2” wide pump, When I bought it I had no idea about spefic sizes. I am 5” in girth and only 5.5 el. i have made .25” girth gain from this pump using it off and on for a couple of years.

Please tell me the advantage of using a smaller pump vs. the one I have now.

Thanks, 5x5

The main complaint about using a cylinder that is too large is that it is difficult to keep your balls from being sucked in. If you are comfortable using your 2” cylinder, then don’t bother buying the next size down. Besides, if you girth is now up to 5.25, the 2” is the one I would recommend anyways.

Hey 5x5 Guy,
I agree with gprent about the nuts wanting to get sucked into the pump using a larger diameter tube.

When you are fully pumped up does you penis look a bit like an hourglass? With a smaller diameter tube I feel that as you grow and fill the smaller tube you will still have an hourglass look, but not as bad because you can touch the sides easier and the pressure will go to the spots that aren’t touching, I think it will be more uniform.
Expansion will go to the point of least resistance “where your penis isn’t touching the tube yet”

I also find that I get a much better pumping session using hot water in the tube, just don’t get the water in your pump. If you are getting a new tube, keep your 2” tube for future use.

When I pump “hot water” I will pump for 10mins. then rattle off 100 jelqs, I use this stagger routine till I get 300-600 jelqs in. So pump, jelq, pump, jelq, pump and so on.
But don’t exceed 5Hg, more isn’t always better, remember the tortuous and the hare story? Well it applies to penis enlargement too.

Hope this has answered your question for you, please feel free to ask more.-Loki2

Well it always looks uniformed, unless I keep it on to long. I have lowered my time to around 15 mins. It dosnt get as big as it used to when the pump comes off. should I increase my time? I have no pressure meter on my pump.

5x5

Hey 5x5,
Try my stagger routine with hat water, just don’t have the water too hot, test it on your wrist first. 15 mins. is too long for one rep of pumping.

Loki

I have no gauge on my pump, so what is the best way to get the right pressure?

I usually just pump Untill its tight? I stop when the lenth gets to the usual spot, I get no additional lenth gain in 15 mins , but time I have pumped for 30-45 mins strait , I have a temporary lenth gain of .25. I know now after finding this site 45 mins. at once is to much.

5x5