Vacuum pumping w/o results.

I have been pumping for almost a year. I have stretched some and before and after. I have had little to no results. I have tried less pressure with more time and more pressure with less time. Nothing seems to work. I am about average size for my age.. What am I doing wrong?? Any advise or routines would be awesome.

s99:

Exactly what has your routine been like over the past year? Exactly what are your starting and ending measurements?

GM

One thing you can try is; Try using a cock ring when pumping.

I use an inner tube as a cock ring and it works good.

I use a very small inner tube from a 27 inch 10 speed bicycle.

Each piece is about an inch wide and I use about two pieces of inner tube. You can use more pieces for more better results. You can use as many pieces as you like, but do not use so many pieces that you do not get a good vacuum pressure going.

Try that it works by holding the blood in the penis.

That was my next step NelsonNelson.. Thankx.. Flaccid I am 5.75 L and 4.75 W. During a 30 minute session I can get 7+L and 7 W. But it tends to donut on me.

speciall99:

PM me your routine—duration/frequency, general health, weight, age, supplements, type of pump, other exercises, lifestyle, medications and anything that would help to determine some sort of a profile. Maybe I can suggest something—Steve

You put the cock ring on and then pump up? Leave it on 10-20 minutes afterwards?
I can see how holding the expansion outside the cylinder would benefit.

You can also put a piece of inner tube at the head of the penis to stop the donut effect.

The piece should cover the head and the part that is donutting.

Yea put the cock ring on a limp penis and let the pump up and get it hard.

Release the vacuum every 15 - 20 minutes and pull the cock ring off and shake the penis a couple of times and the put it back on and then reapply the vacuum

What it does is let blood inter the penile chambers and not let the blood just surround the penile chambers so it get bigger because the penile chambers are getting more blood in them and not letting the blood just to surround the penile chambers.

Thanks man! I am going to Home Depot pretty soon and finding some o-rings! Going to give it a shot later.

You should use something you can remove easily.

If the O-ring works good and you can remove it easily let me know.

I use inner tube now; It works but I would like to use something a little more sturdy.

Wow.. Thanks guys.. I will try that and PM the profile.

I am thinking an o-ring because they come in many different sizes. Should come off pretty easy aswell.
Will let you know.

Have you ever tried clamping after a pumping session? I use a latex cock ring while I pump,( 5 HG for for 15 min), then take off the ring , wrap the base and then slap on a medium Cable Clamp. In Canada they are called Cable Cuffs. Same thing exactly. I got mine at home depo for $2.00. Wrap yourself at the base as far into the fat pad as you can go then clamp it on a few notches. Start wet jelching. You might lose a little hardness at first but put on some porn or something to get you aroused. Then as you get harder clamp down until you are really tight at the base. Continue wet jelching for 10 min. Then take off the clamp and do another pump session. You will be bigger trust me. I also superset this with hanging but that is a different topic. I totally believe this is the way to cement gains in girth. And I think it helps a little in length too. Put it this way.I started PE with a 4.5 inch girth flaccid and 5 inches erect. In the 3 months that I have incorporated clamping in my routine I am NEVER smaller than 5.5 inches flaccid and at LEAST 6 inches erect girth,( usually 6.5 ). And my length has gone up too. Point is try it because it works for me and I love to help any PEer in need. I love pumping too!! But I never had any permenant gains in size until I started clamping with the pumping. Peace and good luck!

OK I made a good Stayer “Cock ring” out of the cardboard thing that electrical tape is wrapped around, Transparent tape, and a velcro cable strap.

It work good and it is easy going on and it is easy taking it off.

If anybody is interested in making one I will scan it and post a picture here so you can make one, and will tell how I made it if you can not tell how I did it by looking at the picture.

The o-rings didnt work, they moved up the shaft as I pumped. That was trying 3 different sizes.