Buckfever's progress report/bananaman story.

Great to hear you added to the extender. Signs that the process is working.

2 and a half years in and I have to say that the process is sorted out, it’s continuing to do the work that’s the challenge. Fortunately we have many examples here of men who persist in reaching their objectives from which we can borrow.

10/29/2019

Late Session:

Low tension @ 60 minutes

Good day, good start!

9/17/2019

33% @ 55 minutes

Only cut it short because pressed for time. Starting a new cycle of extending has given me a renewed focus. I have noticed that I am getting measurements well past 21cm in the extender at the lower tensions. Based on Kyrpa’s work I want to start monitoring the difference in the stretched length at lower and higher tensions and see if these measures over time are colliding.

9/17/2019

Second session:

Low tension @ 32 minutes.

9/18/2019

33% @ 30 minutes

I did not do well with the attachment. I have been putting it off but I think I need to order the large girth base. It’s become a challenge to pull the base girth through the extender and in the morning when I’m still half asleep I sometimes lack the persistence to see to it.

9/18/2019

Low tension @ 10 minutes

Glans condition, needs time for recovery.

9/18/2018

Late session:

Low tension @ 30 minutes

9/19/2019

50% @ 30 minutes

Was pressed for time so I decided to up the tension a little. Attachment wasn’t great but better than yesterday morning, really have to work to get the base fully seated. We’ll see if the X4 girth base works better, you never know till you try.

Seems to go better when I do a morning session and then allow the full day for glans recovery and go for a late session, so we’ll give that a go going forward. I’m on the computer anyway so that’s just tucking it in.

9/19/2019

Low tension @ 43 minutes

Attachment not great but ok. Discipline improving but not as good as it could be. I’ve got to get a little more into the late session routine instead of vegging out at the end of the day, before entering the cave so to speak.

One thing that I should say that I don’t think I’ve mentioned before. I’ve noticed that it’s natural for the skin to become oily over the course of a day so showering up before a late session to get the skin clean definitely minimizes noose slippage. Soap and water is your friend.

9/19/2019

I want to make a mental note of length. Right now with low tension, just strapping in, we are at 21cm at the point of the glans ~ 2/3rds up where it starts to slope down. This is a good reference point as it’s hard for me to see past this point with precision. And at this point my focus is to get to 22cm at this point under low tension conditions.

gentlepsychopath made an excellent point recently on kyrpa’s thread that incremental gains from this point forward are actually quite statistically significant when viewed from the perspective of how each increment enters into outlier territory. I think 1 cm of focus at a time is plenty.

Surely 1 cm gain is plenty in every size category. Statistically every 1 mm even. But looking statistics (and statistics only) with a different angle there is not much value if our dicks fits into 99.7 or 99.9 percentile or what ever. Looking from this angle being large already statistics mean less every gained 1mm. Even being the biggest guy in the TP doesn´t mean a shit, as it is only one locker room. Stepping out we might find out locker rooms being plenty.

Your newly adopted measuring tactics are welcomed. As I am a huge supporter of the harm less principles and using lowest load possible methods, I am looking forward if you can bring some valuable info.

I am glad you posted this as I left some confusion. As far as the measurement under low load, I was only speaking of measurement. I still intend to use the highest load possible that can be sustained for an hour. I think with the extender we are not using loads so large that harm is an issue with regards to load.

9/20/2019

68% @ 55 minutes

Nice jump!!! Managing glans condition better.

Exactly. Loads you extender guys are running can be categorized as low loads. There is the time component added in resulting elongation which is under my interests as well.