Anyone else using a heating pad wrapped around the tube to warm up?

Basically I pump for 10 minutes at 5” mercury, jelq for 5 minutes then repeat this 2 more times before pumping up 1 last time at a very low pressure (maybe 1/2” mercury). After that I hold it on with a blanket while I try to get some sleep for an hour or 3. The pressure is so low that any tilting of the tube could get me and my bed soaked in lube. A blanket draped over the top of the tube while trying to get some sleep is essential as is the very low pressure!

To warmup for the 3 pump+jelq repetitions I use a tube with enough lube to cover my penis when I’m inside the tube and a heating pad wrapped around the outside of the tube. The lube helps with heat transfer! NOTE: even the low setting on my heating pad can get the tube very hot in short time thus I would not dare use this for heat while sleeping. When I am using it to pre-heat the tube and for 10 minutes at a time over-heating did not happen.

I have been experimenting for years trying to find the best way to PE and I am back to the first and only thing that produced results for me in the past which is pumping and manual PE. I thought it was a tiny gain back then but I can see now that by not sticking with it I lost alot! Anyway this routine is a bit more intense than what I did before and I’m using heat better.

I always wrap my cylinder in a heating pad while pumping. Pretty sure that is very helpful for gains.

However, I wouldn’t ever go to sleep with a PE contraption attached to myself.

I always pump with a heating pad wrapped around the cylinder. Been doing it for years and have burnt out plenty of electric heating pads. I have since switched to a Kaz SmartTemp 9.5”X16” heat pad that you heat up in the micro wave. The heat lasts for about 1 hour and you aren’t tied to an electrical cord.

I also use a gel heat pad that you microwave. It helps promote expansion so you can pack the tube quicker.

Have just started using this.

Thickwall pump wrapped in a electric heat pad.. I must say my base girth starts packing the tub very quickly and I will it works wonders. First day so far

Just wanted to update the microwave heat pad I currently use. It is a Thermipaq 6X12 inch available at Walmart for around $10.

I use a heating pad while I pump as well. I don’t advocate sleeping while PEing. That can be dangerous.

It’s a good practice of constant heat,

I do violate some rules of safety cause I’m conditioned to it generally I do one 60 min set cock only. after 60min of full package in a stj and the last 30 min I remove the heat and relax

Ok have done a water pump this morning in the thickwall wrapped with the heating pad for 30 mins.

Less doughnut and more fuller flaccid hang.. Won’t be packing the tube for a while. However with a cockring on did manage to measure nearly 5” girth midshaft which was nice

I water pump and wrap an electric heating pad around the outside of the cylinder. I believe it certainly helps and is a reason I now can do longer sessions before soreness kicks in. However in spite of the heating pad the water in the reservoir cools down during the session and as I do dynamic pumping I have decided to try out a 12V DC immersion heater connected to a thermostat control to keep the reservoir water hot which in turn should keep the water in the cylinder hot. Depending on how well it goes I might be able to dispense with the heating pad as there is regular water transfer between the reservoir and the cylinder during the dynamic pump cycles..

I got the parts from aliexpress and will run them from a 12V power supply. Will probably have to make a water proof sheath out of a bit of small diameter copper pipe for the temperature sensor as I do not believe it is fully water proof.

https://www.ali express.com/ite … 0608.0.0.7kGVLA

https://www.ali express.com/ite … 0608.0.0.7kGVLA

Any thoughts on what temperature to set the thermostat? I was thinking somewhere between 40℃(104℉) and 50℃(122℉).

Approximately how many minutes of heat will this give you Gprent? I’m thinking of ditching the electric heating pad. Wireless seems like the way to go.

I just finished a 30 minute session and there was still plenty of heat. I just fold it according to instructions and for my microwave it only takes 95 seconds to get it hot. For the first 10 to 15 minutes of pumping, you have to monitor how hot your cylinder gets as it can get pretty toasty.

Dude heating pad for sure. I pack the tube soooo fast!

IR lamp for warm up and then wrap with heat pad for pump session. Seems to be going well.

Having a lot of trouble finding an electric heat pad that will wrap around a cylinder (in Australia).