Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Some Help Sizing LA Pump Elliptical. ?

Some Help Sizing LA Pump Elliptical. ?

My erect measurements:

8 inch erect long
6 1/8Th inch erect girth
1 3/4er inch SHORT Side Diameter
2 1/4er inch LONG Side Diameter.

Should I get the 2 inch SHORT Side elliptical ? 11 inch long tube ?

That would give me roughly 1/4er inch room on the short side, 1/4er inch room on the long side, and 3 inches of length room ?

Or should I go for a bigger cylinder ?

First time pumping. Totally new. 6 to 8 months of the newbie program complete, just warm sock wrap and 10 mins stretch. Good positive indicators.

Thanks for any help :)

LA admits some customers aren’t happy with the shape of the tube they receive. Their sizing system has some room for ambiguity.

I’d cut out a piece of thin cardboard into the shape of my shaft at the widest point. You’d need to do a top half and a bottom half, or a left and right half, to scissor is slowly into the correct shape. Then I’d tape the two pieces together and mail them to LA in an envelope.

Then they’d have a pattern to match a tube to. I think your chance of getting a properly-fitting tube would be better that way than by using their measuring instructions.

I have that pump. I enjoy it and we are similar in size but my girth is more like 5” 5/8. If you check out my thread I posted some pics with it. Almost impossible to fill. In the beginning I while soft I pumped my whole package in there. This also depends on the size of your balls. Good luck

Post #387 there is a picture for reference. I came out of that pump over 6.5”mid shaft. My base over 7” so depending on your adaption to pumping this will tell you your limits. Some people have great elasticity and recovery. You have to find your sweet spot.

Originally Posted by AndyJ
LA admits some customers aren’t happy with the shape of the tube they receive. Their sizing system has some room for ambiguity.

I’d cut out a piece of thin cardboard into the shape of my shaft at the widest point. You’d need to do a top half and a bottom half, or a left and right half, to scissor is slowly into the correct shape. Then I’d tape the two pieces together and mail them to LA in an envelope.

Then they’d have a pattern to match a tube to. I think your chance of getting a properly-fitting tube would be better that way than by using their measuring instructions.

Thanks. Appreciate the feedback :)

Originally Posted by BigFinisher
I have that pump. I enjoy it and we are similar in size but my girth is more like 5” 5/8. If you check out my thread I posted some pics with it. Almost impossible to fill. In the beginning I while soft I pumped my whole package in there. This also depends on the size of your balls. Good luck

Thanks. Where can I find your journal ?

What size elliptical did you buy?

What size do you think would fit me ?

You can click profile button. Search through my posts. My progress with pics is where you would find it. I have the pump you are looking to get. If you are going for length this pump will work if you use silicone sleeves.

I decided to buy the 2” Short Side, Elliptical. This should give me about 1/4” room on both the Short and Long side.

If it’s too big, I’ll buy the next size down. If it’s too small, I’ll buy the next size up.

Should be fine. I’m definitely not 7 inches girth circumference yet.

I will also buy the cock ring for my ED + silicone sleeve.

Originally Posted by BigFinisher
You can click profile button. Search through my posts. My progress with pics is where you would find it. I have the pump you are looking to get. If you are going for length this pump will work if you use silicone sleeves.

Was this Universal Pump Sleeve, the one you recommend ?

Universal Pump Sleeve – L.A. Pump

The elliptical cylinders are a little tricky. When I first got one, my round cylinder was 1.75”, base girth was 5.5”. I regularly packed that cylinder 2/3rds of the way up.

So I got a 1.75” elliptical and I could never get a good seal on it. So I saved up and got a 1.5”, that worked much much better.

I kept the 1.75” because I think I’ll eventually grow into it.

Just a heads up, you may find you need to reduce the regular amount of pressure you use when you go from the round to elliptical cylinder. I am not good at physics so I cant explain why but the same pressures feel higher in an elliptical than they do in a round cylinder.

Best of luck and keep us posted on your progress!

Top
Similar Threads 
ThreadStarterForumRepliesLast Post
Vaccum pump cylinder sizing questionricepattyPenis Pumps301-09-2022 07:41 PM
Help with cylinder sizingFL_TitanPenis Pumps911-24-2012 04:51 PM
Sizing my Veseal cylinder order help?JackovDiamondPenis Pumps508-03-2010 12:09 PM
Split Collar Shaft to increase Ball Hang. Opinions and sizing help please.kushextenderPenis Enlargement1001-22-2008 12:01 PM

All times are GMT. The time now is 01:09 PM.