How to use an extender at high tension without slippage?

I’ve been at extending for roughly 4-8 hours a day for 5 months now and I have used the bathmate hydroextreme for about a year now. My starting stats for this forum are 7.2 long by 6 around. My erection quality varies so my length can go between 6 (a little soft) and 7.5 (absolute horniest) depending on arousal, but the girth stays fairly consistent. If I compare pics from 4 years ago (definitively before I started PE) and now, I notice I’m only slightly bigger, so I don’t know if it’s an EQ thing or if I’ve actually gotten bigger. My main goal is to gain length as aggressively as possible. In 5 years I want to be at least 10 inches.

I currently use the quick extender pro at an extension length of 8 inches top to bottom of the device. I’ve been using it for let’s say pessimistically 4-6 hours a day with no rest days (I never feel pain or discomfort apart from on the skin) up until I added the last 1/2 cm extension bars, after which I am having trouble pulling my dick far past the bars so that when it pulls back it stays on properly. Even with the dual strap system, it slips out after 15 minutes or so. To combat this I shower beforehand to remove oil from the glans, I wash my hands before I touch the glans to put on the device, and whenever it slips out I wash my hands again before restarting. These tactics worked well until now.

Now I have to use the bathmate to build fluid in the head so that that fluid serves as a knot of sorts to keep the device from slipping. Even if you don’t use the edema buildup, having some blood in the glans helps it withstand higher tension without slipping because the comfort pads can “grip” around it and it acts like a knot. On this note I have bought a couple different sized clamps to experiment with. I’ve found that clamping above the pubic bone with wrapping sucks, so I just clamp under the balls. I’m going to start clamping for 10 minutes before my all day length workout in order to build up blood in the glans.

I feel like using an extender would be FAR more effective if I could eliminate all slippage from the equation while still using the most aggressive possible tension, meaning I stretch it manually as far as it can go and TRAP it there. The few times I’ve had sessions like these by some fluke of luck I would feel tension in the entire shaft, and it was awesome until it started hurting the skin from it pulling back millimeter by millimeter.

So to the veterans here, what’s the best way to CLAMP THAT SHIT DOWN and prevent it from slipping at high tension while you’re extending?

You might try a self-adhesive Ace bandage wrap. Cut a 2” bandage lengthwise to make 1” strips. Do a two layer wrap. It will spread the load out from the noose or strap and stick to you and the extender’s sled.

Non-vacuum extenders work best if your glans is larger in diameter than your shaft. If it’s the other way around… that’s why my extender wound up in the Big Plastic Tub. I couldn’t figure any way to stay in there that didn’t involve Super Glue.

Ever tried using a gauze wrap? Check idunnowhy’s thread post, he uses the same extender as well.

Can you please post a pic of how to do this properly? What you’ve described makes me visualize wrapping around the sled and slightly touching the shaft from above and below, and this doesn’t seem like it would take off much of the load.

I typed idunnowhy into the search bar and all that came up was his routine post but there was essentially no content in it. I don’t know if it’s because I’m a new member or not. Could you please link me?

What is your current loading? There should be tension lines at the bottom of your bars, how many are showing when you strap on the extender?

The pumping will increase your glans size; however, the edema throughout your shaft could negatively impact the elongation process.

I’m not sure what tension lines you mean but you can contract the device for 3 of those little “lines” and strap in, then you let go and it will expand again, producing the desired stretch. What happens is the head of my dick will be above the top of the device when I have the thing compressed but as I let it sit and decompress, it starts to slip and the head goes maybe half a centimeter below. In other words, it doesn’t stay put. I am still making gains over time but if I could prevent it from moving at all that would be perfect. If by loading you mean what kind of tension are the springs in my device, it’s 3500 grams. I’d be fine using a 4000 gram one too, but I don’t think it actually impacts the growing process because as long as there is sufficient force in the comfort pads and tubes to hold the penis in place with the head at the top of the device it doesn’t matter how hard the springs are pulling.

When you let go after strapping in do any of the tension lines become visible again?

Yes, as I would hope they should. This would mean, if the penis stays aligned with the top of the device, that the tension is extending me past what I could do with my hand alone. In practice what happens is some slippage combined with some extension, which is why I’m so interested in how to clamp that shit down airtight no slippage whatsoever.

How many become visible? All three, or just two, etc.?

Do you then have to use the dials to increase the tension?

All three become visible, and by the time the third one is visible about half a cm of slippage occurs. I don’t touch the dials.

I always had the noose style slippage problem with my 4X Labs extender. But I discovered that if I wore the Phallosan a high tension for 45 minutes, and then switch back to the extender, my glans would have enough of a pump that it would not slip out, even at the highest tension.

Your glans position in the cradle might slip a bit, but up to which tension line can you go without it slipping out?

I ask this, because if the glans settle(slip) a bit and you’re then able to maintain tension without the glans slipping out completely, then you are probably good.

You could also try reducing the length of the bars so that when you let go the tension is not enough to cause your glans to slip, from there, then increase tension just enough up to before the glans begin to slip. After 20 minutes, increase the tension slightly using the dials. This is using a warm up at lower tensions to support your process.

Also, applying heat can also help.

Can you increase the compression of the noose? My experience is with using an actual strap, so I’m less familiar with the noose style systems. Buckfever has significant experience using a noose style, you might want to check out his thread.

I think that if I were to find a way to make it so that the device does not expand out after I strap in, I can let it sit there for a while until the glans has ballooned a bit, after which I can increase the tension, and that would be the ideal solution. To answer your question, it depends on how ballooned I am. If I’m having a really good day it will stay with 3 tension lines visible (max expansion) but most day it will expand to two visible and stay there for a bit, but because the device is applying pressure to expand to 3 lines visible, it eventually slips.

Your idea sounds interesting and similar to what I described above. I have never touched the dials on the Quick Extender Pro at the bottom, those little wheels. This is because whenever I have, the device gets fucked up and the bars become uneven or gaps appear between the first extension bar (built in) and the first 1/2cm extension bar (also built in) at the bottom of the device. Please let me know if you understand what I’m describing; it should be clear from looking at this photo:

https://www.goo gle.com/url?sa= … QAAAAAdAAAAABAD

That said, how do you use the tension bars properly?

The phallosan is a vacuum extender right? What do you think of it? Do you prefer it to a noose extender?