Prevent blisters wIth vac-hanging

Now try adding baby powder… and your glans is cemented :D

I agree that the baby powder is a good trick. It is nice to have a cemented dick - but my wife is complaining that it’s uncomfortable!

:)

I am sure she will “adapt”. ;)

Great tip on the baby powder. I have an ADS I have been worried about using because instructions warn about blisters. Now I know just to dump a little baby powder in.

I use it meanwhile on everything.. stretch, clamp, ads, adc.. salad,..

Remind me not to come to dinner at your house.. :)

I’ve been using the Vachamger 3 for over a month now, currently 10-12lbs. Not had a blister yet and I use 2 different types of tape. First I wash my glans with soap and warm water, drying well afterwards. This makes sure the tape sticks properly. Then I tape the entire glans and frenulum with 3M micropore tape, and put a criss-cross of 3M microfoam over the tip for extra cushioning. My glans come out perfect even after a hour straight. To help removal of the tape, I use hot water and a bit of soap. I find you do have to watch out for any juices (piss or precum for example) you may have in the urethra as this can loosen the tape and allow expansion.

When sucking out the air, I like the glans to travel all the way to the air hole in the Vachanger cylinder until it blocks off the air hole.

I did the same thing as you Goss and never got any blisters with the vac3.

How much weight are you guys hanging with this setup.

I’m hanging between 13-16lb for 2 hours a day at the moment. Have hung 20lb with no problems.

I’m going to try your wrap technique, I’ve gotten a water blister a couple of times, hate having to stop while it heals.

Hey, I’ve just made a slight change to the tape wrap technique, due to the higher weights. I do the criss cross over the urethra, then wrap around the entire glans and down the shaft at least half an inch below the coronal ridge with micropore tape. The front edge of the vacuum cone then sits over the tape. I find it much more comfortable. Sometimes at higher weights I found the vacuum cone could force the tape to move and cause discomfort. I get through a roll of tape a week.

So I’ve switched to microfoam tape. I criss cross the tape over the urethra and then add 2 strips to cover the diagonal areas of the glans. Then I set up the LG how I did Max-Vac and I got to say I’m on my second or third week back and I’m up to 7.5 lbs but this is way more comfortable than the micropore tape and doesn’t pinch. I also don’t need water just to get it off and I can reapply 2 to 3 times more. Microfoam is silicone based which is gentle on skin, elastic and its thicker to protect from the vacuum. I haven’t gotten back to heavier weights, I’m coming back from almost half a year without hanging, but I see this being very promising.

Here is my setup, I have at MOS, I will work on getting it over here too. Anybody with an LG want to test this out let me know how it goes.

I’ve tried these out and while it did work at close to 9 lbs it seemed to pull funny on my glans, especially the underside. Made my penis look like it had an under bite haha. I did get some edema, a few times I had to stop the set because of itching = BAD SIGN. I think this method is quick, cheap and good if you have it available but I’m not sure I could handle much more weight, in fact I’m quite positive that if I were to go up a little more in weight I would be getting blisters. I’m thinking the way I already set up, with microfoam tape, will be preferable as I can really control the amount of compression, my glans doesn’t deform and I’m sure I’ll be able to go much higher in weight when I get there.

If it works for you keep at it, but I’m not sure how much weight you could go up in. The microfoam tape I bought through amazon doesn’t beat up the skin like micropore tape does, its thicker and more elastic and I can reuse it once or twice before I need to get new strips. I paid close to $25 for 12 rolls which should last me close to a year, so the price isn’t that bad if you budget for it. Still this is a great innovation, not for me, but thanks for bringing it to light for everyone else.

Would you please let me know the brand name or amazon weblink ? I am very interested to purchase a good Micro foam Tape.

Thanks

this is what I bought:

http://www.amaz … /dp/B0013Y595I/