Homemade Tubes?

Thanks for that information 8.5, it’s very useful. I ordered a universal sleeve from amazon, looks like it may work. I’ll be getting down to business soon. Just hope I can get to the mail box before my wife, she’ll ask what it’s for.

I found it here:

http://www.amaz on.com/gp/aw/d/ … edir_mdp_mobile

I have been a pumper for some time now, off and on. I have not used it for gains but for the sensation provided. However it is not bee very satisfying of late. I built my own after the commercial model I had broke at the inlet. I have retained the bulb that powers the suction and added it to am eight inch length of 2” PVC pipe, with a capped end to which the suction tube and bulb are attached. Here is my frustration. I get only limited suction, there is only a small amount of gain. I have seen that some men get their members to elongate significantly. Is it the bulb being too small to carry the full evacuation of the tube or some other reason? I would like to fill the tube with myself and retain the size for at least enough time to jerk off or have my lady do me. I also take med’s for diabetes and blood thinners. This is a barrier I can’t get by. They are so strong as to defeat all forms of current E.D. Products. Pumping is the best alternative to radical methodologies. Can anyone help the newbie please feel free to comment. Thank you.

In 1997 I shared a design (that I had piad $20 for!) that used a clear silicone caulk tube from a specific brand. I don’t think it’s sold anymore. Wrapped electrical tape around the base to provide larger contact area. A piece of bicycle inner tube pulled over that and folded inside made a good seal, and if cut longer made an incredible masturbation device. Problem was it the tube was 2-18” ID (if I recall) and in a few months of PE I no longer fit into it. I spent more than a few unsuccessful hours trying to figure out how to widen a caulk tube ;-)

Vacuum Penis Pumping - Classic Site - Tom Hubbard

Ah hahahahahaha leave it to mem!

Made my first pump. Being a mechanic for a living made things easier. I found several lotion/hair spray/drink bottles of varying diameters, all of which use a standard size soda bottle cap. Drilled a 1/2” hole in the cap and installed a valve stem (valve removed of course) and then mity-vac pump and gauge. Gotta say, I’m hooked. Find myself just staring at my pumped sick afterwards! Anyway, just thought I’d share the valve stem and soda cap idea, makes for easy tube changing! I also used 3m thin weatherstrip on the bottom of the tubes. I made a whole package tube as well, with a size matched oil filter gasket on it. What a fun new hobby.

I spent the weekend pumping my cock. I start out with about 5.5 flaccid and after a long session it is about 7 long and fat. This lasts for about 1 hour or so, but the fatness stays overnight and makes morning wood very impressive for me. My mate likes helping me pump too. Although the gains are temporary, for me it is welcome and beneficial to my mental and physical well being. I will continue pumping as a means of penile satisfaction and gratification. As a consequence of illness and blood thinning medication it is difficult to spontaneously erect. This is a good thing.

Nothing I have found works better than these..

Super
Cheap
I have to two stage because these are a little small for my width but these are very durable and should work for any length coupled with a mityvac pump very good

Interesting first post. How do you deal with the attachment to the pump?

Oh, and welcome to the posting side. 6 years to your first post. That’s got to be close to a record.

None of the online info at your link or any other site I’ve found them at give any dimensions of these tubes so, you got some length & inside diameter info? And how clear are they?

I tried to make my own pump a few months ago but could never get the seal right and air always leaked.grr

May I ask how to buy? That a good point? Specifically how to operate a day for how long? Using a long time okay?

The paint ball tube I used app 2 1/4 x 10 long
Heated it up flared the end out put some quick drying epoxy in the flair for strength

I made back in 2007 link to post below
Used it regularly for over 4 years
Bought a better tube
But I stull use it occasionally

Original post
cruzingratiot - Homemade Tubes?

If air is leaking at the base of the cylinder then I can definitely recommend applying plasti dip to the base of it. A few layers of that makes it incredibly comfortable and I have yet to have any sealing issues after applying it to my most recent cylinder.

I bought acrylic tubing from this website a few years ago:

http://www.tapp lastics.com/pro … rylic_tubes/141