Large Girth Extender

Ok been doing PE now for a while. I’m growing out of my standard stretching device. I’m looking for a large girth strecher now. Any ideas

What do you mean large girth stretcher?

Extenders are generally for length, although some girth may also develop from use of an extender proportionally. Other will use other techniques such as jelqing, clamping, pumping ect for specifically girth. If you’re not already, I’d encorporate manual methods such as jelqing, horse squeezes and such depending how experienced you are with girth exercises.

You need a bigger base I understand? I think there are some out there to buy . X4 labs has one for their extender.

X4 labs is the only one I’ve found and what I used personally in my extender days. If your girth exceeds that extender, you are out of luck. No other company offers a larger base at this time.

Sorry, my mistake. Looks like I miss understood what you were looking for. When I used to use the X4 extender I upgraded to the large girth base after some time of use. This was because my penis fluctuated in size alot while wearing it and when it was pumped up, it was too big for the normal base and was very uncomfortable. However when wearing the wide base and my dick wasn’t at that bigger point, the wide base seemed too big and would cause my dick to sit in the bottom portion of the base (not centered) leaving the top portion open and thus reducing the tension applied due to this also leading to more possibility of slippage.

As for dimensions. The standard base accomidates upto around 5” girth and the wide base accomidates upto around 6.5” girth.

I believe the 4X wide base is only wider vertically and not horizontally because it needs to maintain a standard width. Accordingly, it will accommodate a larger girth, but only allows the additional expansion on the top and bottom of the shaft.

You are correct. If one could find or create a glans connection piece compatible with a greater distance between the two rods one would create a base wider than the typical industry standard.

Such a thing doesn’t exist in the market right now. And I doubt Monkey Bar is interested in it.

Sounds like you’re going to have to tinker with and chop and screw your old base into what you need.

Show some pics of your new creation if you get around to doing that!

I filed out the base of my JES Extender today a bit. It has helped but I need to take out a bit more. Using a round file and 100 and 1500 grit sandpaper.

I never even thought of this as an issue! I guess the Penimaster I wanted is out of the picture given my 6” girth. Thanks for the thread!

Right on, dt.
I upgraded mine to a wide base because the regular one was a bit snug if I started to get “chubby.”

It’s ever so slightly wider, but the majority of the increase is dorsal/ventral. I’ve added padding to reduce that, but it’s still looser than it needs to be.
As an amateur machinist, I’m pretty sure the device would accommodate a wider base for most users, but if the rods were short the angle could be too much.

What I’d really like to see is a wider base, narrower “vertical” opening, and a wider set piece for the end sold along with it, so it would align nicely. If I’m able to, I’m going to widen both the base as well as the strap piece, as well as modify the area into which the posts rest to make donning easier.

I guess I’m going to pick up some aluminum and go to the mill and lathe and make something work

If you are machining a special base, you should also machine a new piece for the glans.
That would be the best set-up.

As mentioned above, the X4 extra girth base is only extra in the vertical, not the horizontal. For me it was uncomfortable as hell because it is almost skinny to the point of being sharp and not having enough surface area to distribute the force comfortably.

Good luck with the project, you have to post some images of the end product.

Hey, if you’ve got the skills an resources..
My ideal extender would be to 3D print the parts in wax and then machine aluminum castings.

I was thinking about taking the standard base, indexing it in the mill, and opening it up with a boring head. Then, if need be, warming it up in an oven and stretching it laterally to make a nice wang-shaped oval.