Oh looky here! The CCH3.

Hey CC,

I finally made one but I am having a hell of a time attaching the thing. Not quite sure what I’m doing wrong. The two tubes just roll right off my penis everytime i add weight. I’ve tried it with and without a wrap. Any ideas?

Yep! What has happened is that the S-hook has made its way to the other side of the hanger, meaning it leaped over the ends of the pillars to the other side. To the untrained eye, it looks innocently normal enough until you use it.

The pillars should rotate in a “wax-off” rotation ( remember the Karate Kid movie? ). With the S-hook on the other side, they do a “wax-on” rotation and roll off the penis.

Just work the S-hook over the ends of the pillars to the other side.

Wow I must say ChickenChocker this is a great device. After hours and hours AND HOUR of trying to make this thing, I finally got it working :D . This is my first hanger and it seems to work perfect, thanks again man.

CC,

I’m also having a problem with the clamping when a weight is applied. It simply doesn’t grab when the weight is applied.

I think that it is due to the cord I used. It is too coarse in its winding and so does not pull freely through the hole in the pillars.

I will try a finer cord and see what happens.

Has anyone else had this problem?

Initially I did have that problem. I had to smoothen the holes and use a different cord. It still grabs a bit but not as much. Drilling pvc plastic does produce splinters so you have to put a match to it to get out the excess splinters.

good luck.

That’s why I use that nylon Mason line from Home Depot. You have to melt the ends because they unravel easily but the cord surface is very slick. Also make sure you are not having the same problem as dan001 is having in the post above.

CC,

I think bigflip had the same problem as me (the CCH3 grips, just not very well) and seems to have solved it.

Thanks again.

You’re welcome.

Even though you don’t need to assist in the grip of the hanger, if you want a snug lockdown fit, just pinch the pillars together with a thumb and forefinger after they grip the shaft.

Hi CC
Still hanging comfortable with your CCH3. I am going into my 2nd full week out of 3 with the CCH3 with two days of rest of course.
Still at 5 lbs. 3 sets@ 20min.each. I think that I will have to add more weight soon Hmmm…
Remember I said I was using the gray hard electrical pipe which measured 1 inch O/D.
You said the white measured 1 6/16 inch o/d.
Do you think that the size pipe I am using is to small?
I have some white pipe around maybe I should try to make another?
I also noticed that my Pads stretched because there is a dent around the hole. Any advise if I make a new one.

Take Care 4by4

As long as the surface of the gripper pads are about 1” long along the shaft of your dick, it should feel plenty comfortable and you shouldn’t need to make another until maybe you are hanging with over 10 lbs. and you feel that it could be more comfortable with a larger gripping surface.

If you want the surface to not dent in:

1. Take a flat rectangular piece of firm flexible plastic ( maybe a half-inch wide by 1 inch long ) that won’t crack and stick it on the gripper surface inside the pillars. This surface should still be sticky.

2. Then, drill a hole right in the middle of the pillars so you can screw in a bolt horizontally to push against the surface of that plastic. This takes some accurate eye-balling.

3. It’s not really pushing the plastic, but it’s barely touching it and I needed to cut the bolt just right so it is the perfect size. I did this with mine a few days ago and I will add a picture of it here soon. Be careful when screwing in the bolt straight because it will stray off-center and you’ll have to work at it to keep it headed straight for the plastic.

The nice thing about making the CCH3 is that it’s so inexpensive and once you make one, you have plenty of parts for another, which is easier to make since you now have the hang of it.

Here’s a great shot of the reinforcing bolt installed in the CCH3.

The plastic piece inside I’m using is a half-inch wide and under 2” long.

I cut it from a fishing tackle tray compartment partition.

Thanks CC
The picture makes it easy to understand. I will try this. Like you said I do have the extra parts so in my spare time
I will attempt to make a second CCH3 using the correct size pipe. Will let you know the difference of feeling between the two, 1 inch OD verses 1 6/16 OD

4by4

Well after jumping my hanging weight last week from 10 lbs to 14 lbs it looks like I gained 1/8” but I won’t say that officially until I get to 6.25” BPEL.

But after reinforcing the gripper pads so they now have a perfectly flat surface like a classic AFB hanger, I must say that the last 2 days of hanging 2 hrs each day has left my shaft a little sore last night after the last session.
It was sore where the hanger attaches right at the very sides. I guess I’m not used to the flat surface with the new weight. I’ll modify it by slightly loosening the bolt or remove it altogether. It’s a personal preference thing and I guess I didn’t know I had it so good without the bolt there.

So what’s the point for cutting the windows out if you need to reinforce the gripper pads anyway. Or is there something that I am missing here?

That is a very good question inamo. My guess is that the reinforcers dont help that much.. But I bet you could just not cut the windows out and it would still work well.

On another note I was thinking of putting some theraband wrap over my grippers so I wont have to wrap at all.