The big penis and mens' sexual health source, increasing penis size around the world.
:thumbs:
Before: I'd like to show you something I'm very proud of, but you'll have to move real close.
After: I\'d like to show you something I\'m very proud of, but you guys in the front row will have to stand back.
God gave men both a penis and a brain, but unfortunately not enough blood supply to run both at the same time. - Robin Williams (:
I have a question though. Are people recommending gluing the foam to the part that mm covered with blue duct tape?
Or should there be some slippage?
Mr. Happy,
I used duct tape to tighten the fit of the foam on the plastic roller. I wouldn’t recommend gluing the foam directly to the plastic.
On mine, I do have a minimal amount of slippage, maybe a 1/16th of a turn per jelq if that.
mm
Thanks man.
Great thread. Nice work.
Before: I'd like to show you something I'm very proud of, but you'll have to move real close.
After: I\'d like to show you something I\'m very proud of, but you guys in the front row will have to stand back.
God gave men both a penis and a brain, but unfortunately not enough blood supply to run both at the same time. - Robin Williams (:
Well, I went out “in search of” today and got zilch. Hell, I didn’t even know it, but my local
ACE has been shut down!!! Go figure! I have heard today that there is one other spot here
that may have them, so I am going to check that out tomorrow. Thankfully, the ones I ordered
online will be in tomorrow. I am going to get the foam and a set of paint rollers as well and give
them a try.
kook
Keep working, keep learning
KEEP GROWING!!!!
These two threads should be linked together so we don’t have to repeat ourselves as much:
Power JELQ (canning tong) techniques
Hap. Don’t glue anything to the rollers. Simply cut your pipe insulation 1" longer than the rollers. The 1/2 inch of excess foam on each side locks into the canning tongs and keeps it from spinning. Kooky: Making it with the longer tubes puts a bow in the rollers that helps keep you dick from sliding to the side and gives you room to get your fingers in there to hold your dick. It will still slide if you let it, but the longer rollers help by giving you more surface area. There is definite a learning curve here, after a while you just get good at it. Thumb of your free hand on the dorsal side of your dick and middle finger under like your taking a piss. This hold slides in and out with the jelq. Press deep into the fat pad then pull all the way to the end. JelQ ten minutes and Clamp for ten.
Did I just say all of this? :rolleyes: I’m having de’ju’vu.
2003: 6X5 2010: 7X7
No Nukes
Brilliant!
Penis Enlargement Forum -- How To Jelq -- Free Penis Enlargement Videos
Make a Donation This place runs on donations, help out if you can. Thanks.
I’d like to point out the fact that over pricing the original PJ at 60 freaking dollars is a prime example of price gauging backfiring on you. It cost less than 10 dollars to make these things. If they would of just priced them reasonably, we probably wouldn’t of went out shopping all over town looking to make them ourselves!
10 dollars to build one (less if you bought in bulk), then maybe three to ship them out(less if you buy in bulk). I’d say a proper price would of been 25 to 30 at the most. They would of sold allot more, and most likely made more money with much less competition.
In the land of the blind, the one eyed man is king.
Back when I bought mine three years ago I think they were going for $29.00 Even then people talked of them being nothing more than canning tongs and pipe insulation. But $60.00 is ridiculous. I’m still wondering of the legality of selling a device made from another patented device. Mine laid in the closet for three years forgotten because I was busy using different methods until these threads started up. I’m glad we looked at this gadget again, and worked out ways to make it cheap and improve it to boot. I’ve already got a stack of them over here. I figure they will break sooner with the longer rollers, but I don’t care. There almost disposable.
2003: 6X5 2010: 7X7
No Nukes
I think the homemade version is as old as the commercial version BG.
Penis Enlargement Forum -- How To Jelq -- Free Penis Enlargement Videos
Make a Donation This place runs on donations, help out if you can. Thanks.
Probably older.
2003: 6X5 2010: 7X7
No Nukes
I don’t think so.
Penis Enlargement Forum -- How To Jelq -- Free Penis Enlargement Videos
Make a Donation This place runs on donations, help out if you can. Thanks.
My canning tongs came in today and I gut the foam that has the self adhesive taped ends.
I also got one tube of the pre-split and I have some setting from the glue right now. I couldn’t find
any of the non-split kind.
kook
Keep working, keep learning
KEEP GROWING!!!!
Wow, this homemade device looks very promising. I will try to build my own one!
But I live in Germany and don’t know where to get those jar lifters from. I have found one, but it looks not as useable as the one you have used, mm.
Here’s a picture of it: ~ click me!
So I think that I will get one from eBay.com. There are some jar lifters and they are quite cheap, even with shiping costs to Germay. "Quite cheap" means: no $59 like for the original device.
If anyone has a source for a nice jar lifter (with rolls) in Germany, please tell me :) !
JJ
01.01.04: 6.75" BP x 5.50" . . . . . Next Goal: 7.50" BP x 5.50" . . . . Pics
01.03.04: 7.15" BP x 5.50" . . . . . Ultimate : 8.00" NBP x 6.00" . . . . Progress Report
Now someone needs to invent the autojelqer it would look like the power jelqer but it would go by itself. You would adjust the tension and speed and it would move the rollers down and tighten than move up an adjustable amount and than release and repeat the process. Now that would be f-ing brilliant and a product I would just have to own imagine just slipping your autojelger on while watching TV or surfing the net and reading the forum.
I haven't failed, I've found 10,000 ways that don't work. Thomas Edison (1847-1931)
Now someone needs to invent the autojelqer it would look like the power jelqer but it would go by itself. You would adjust the tension and speed and it would move the rollers down and tighten than move up an adjustable amount and than release and repeat the process. Now that would be f-ing brilliant and a product I would just have to own imagine just slipping your autojelger on while watching TV or surfing the net and reading the forum.
That made me recall this old thread: Futuristic PE