The SuckXtender - just remember it sucks!

Without checking I can’t be 100%, but I’m fairly sure that with the Jes the spring loaded part is just one of the attachments, so you could remove that and replace it with a pair of the spare static ones. Mine is buried in a pile of boxes in the spare room at the moment, or else I could have verified that.

Using the spring loaded would mean you have an increasing tension on the penis?

Using the static rods would mean you have the penis in an elongated state, but it remains at the same amount of tension? Would this also allow for an increased wear time?

The other way around, sort of. With a spring the tension will remain fairly constant (change in spring length affecting force excepted) since it will move as the tissue moves. Using a static rod would exert a given force at a given length, then as the tissues stretched over the course of the session the strain would reduce. I haven’t tried this personally, though I would expect that it would make things easier on the tissues over the period of a training session, which may counter some of the fatigue accumulated over the same period. Perhaps someone who’s used it would chime in the confirm or deny that.

With the suckX I start a session by pulling out a good extension and screwing up the fixing nuts, then wait a few minutes, then I’m able to pull it out a bit more (0.5”roughly) to its maximum extension. At this point at the beginning of a session the tension is definitely greatest. After an hour, at the end of the session, the extension is the same but I can defintely feel a reduction in the tension.

Thanks mbuc.

Is this device similar to the one you have been using Mbuc? http://www.fore skinrestoration … fo/vacutrac.htm

Had a quick look at that site and it would have been a lot clearer with some diagrams or pictures. It seems more like a pump - you stick your dick in a tube and pull a piston.

The device I am using is a stretcher that only pulls on the glans. SuckXtender
There are pics of it in use here

I’ve looked at the pics, but I was a bit curious as to how the device I linked to would work, and if it was similar to yours. I don’t know if it slides over the entire shaft or if it can be used on just the head, as it is foreskin restoring device as well as a lengthener and also used for girth as well. The main reason I was wondering about the similarites is because of the weight attachement at the end, and if you used a sleeve you could achieve the same end as your device, but I don’t know since they don’t show it in use. I think if we saw it in use it would clear up the question.

Ok, here is my version. The only significant change is to add a valve which gives me the ability to draw and measure a vacuum.

5lbs of wt= apx 3 in hg.

The size got a little out of hand, but I only use it at home.

Nice one, sparkyx!

I would like to have an attachment cup with a pressure tapping but I can’t find a readily available cheap vacuum gauge here in the UK. Mind you I haven’t looked very hard and would only pay a few quid.

I’m glad you say that 3”Hg will support 5lb weight/tension - that is the ball park figure I thought the vacuum should be but had never measured it.

I notice you haven’t shaped the base ring to make it thinner between where the two rods attatch. Is it comfortable to wear straight up and straight down?

What are your impressions/thoughts on using it so far?

There are a few vacuum gauges on ebay.co.uk right now that are currently bidding in the £1-2 range. Looking at completed listings there seem to be a lot of this model actually selling for that price (+ P&P of £1.40). I don’t know what kind of quality they are, but they certainly look much better than the one on my manual vacuum pump.

Thanks, I’ll have a look.

You don’t need a vacuum gauge, you can just apply a light vacuum, and you can judge it by hanging a wt and seeing whether it is enough to hold it.

Shaping the base ring…hmmmm…yes that would help! And no its not comfortable SU or SD just because of it pulling the shaft up and over the rim…great suggestion!!!

My impressions so far…far too big to conceal.

Great in that it distributes the vacuum force over the entire glans which makes it both more comfortable and serves to expand the glans at the same time….great combo!

Far too easy to use too much force. What really is needed is to put on either the wt or the gauge and measure the force each time. As of yet I can’t really acurately judge it.

Over all, I think this is really the way to go. I add pumping 1-3 days a week, and I think its a great program.

Its just a matter of finding best time/force/frequency.

The great thing about these two together is its quantifiable and reproducable.

We will be able to pass on what works for us, which will then give others a fairly good starting point to reproduce the results.

I just made a vacuum cup with a valve for hanging Monty’s golf wts.

Its even simpler and easier that the last one. Its to keep Monty’s wts on easily and solidly, while also getting a glans expansion.

Its made from a baby food juice bottle and the green valve I bought at Petsmart in the aquarium section.

I will use some bicycle inner tube around the neck for improved seal, like on the one pictured above.

Just made a new pair of rods (the old ones were getting too short :) ).

I tried to bend the end of the rods to save welding on a bit at right angles to fit into the base ring. However the screwed rod broke before bending 90’.

Not to be defeated I heated up the rod in a gas flame and this time it bent beautifully using a pair of grips/pliers. Then I just had to fit a nut inside the base ring and trim of the excess rod with a hacksaw. Because the nut tightens the rod to the base ring I think this is a better way of making the rods, as well as being easier.

The models just keep getting better and easier!