Finding xeno: a penis tale

You should have asked him if he knew where the cable clamps were. ;-)

Now that’s funny :)

xeno

BPEL=9.375.

It’s only been a week into P-phase, wearing CC through the day…will go for another week…but seeing a solid 1/8” gain. I actually think it’s possible that I register a solid 1/4” gain somewhere into the R-phase, we’ll see, but for now, happy with the 1/8”.

xeno

Got a new stretch: wearing a CC (or 2) and sitting at a desk, place your crossed legs on the desk in front of you, now reach around your left leg with your left hand and grab the CC, now pull like the dickens to your left. Repeat on the right side. The CC serves as a handle to provide a great grip. This stretch puts great stress on the suspensory ligature and fascia; and really targets each side of the suspensory apparatus. If the Sumo Stretch and the Bucking Bronco stretch don’t give you a lig pop, this stretch might.

Don’t know what to call this stretch; any ideas?

xeno

Anaconda Stretch? I wanted to try somethin’ else but that keeps comin’ to mind.

Works for me; Anaconda Stretch it is. Thanks for playing TG :)

xeno

I’d like to ask a question if I may. Xeno, I’ve seen many talk about a lig pops, do you feel it is necessary to have lig pops in order to achieve gains? Thank you.

No, I don’t think so, but my experience causes me to think that they help.

xeno

So I decided to make a TTr and was going to go ahead and buy more nuts and bolts to make another TT, this time with no spaces between teeth and a steeper peak. Because of your story I was seriously paranoid at home depot haha. One of the workers asked me if I needed help when I was buying the molding and then I saw him in the hardware section later on and when I made eye contact he looked away.

I might not apply lacquer to it this time. I included pics. Something that has helped me is to use a pair of channel locks and a wrench to fasten the bottom nuts down. This has eliminated allot of play for me as before when I tightened the wingnut down the bolt would spin with it. Now it tightens perfectly and I’m getting really good workouts in. Will try my new toys out tonight if the glue finishes setting. Also I precut the 1/2 inch boards from last time and used them with my new corner molding. I had some overhang on one side so I glued some toothpicks below and on the inside of that piece to sturdy it. What do you think?

Honestly, ls, I can guarantee you that at the forces being exerted by Tiger’s beastly CCs under full compression those triangular pieces would break. As such, I wouldn’t use it; not fond of splintering wood and Tiger being in such close proximity. In short, I’d swap out the hollow triangles for solid ones. Ditto for the TTr.

Not only is safety important, but so is the ability to produce increasingly higher forces…without failure of the device.

Sorry; but you did ask me what I thought.

Beautifully executed build though.

xeno

Damn subbed to this thread. Good job man your an insipiration!!!.

Hmm it felt sturdy enough last night. Maybe I can cut some triangular pieces of wood to wedge on the inside though because I don’t want to risk it

:up:

xeno

Well BPFSL is now 10.00”.

From my 6th post in this thread, dated 6/14/2005:

My current BPFSL-BPEL value of 0.625” may mean that I’ve got another 0.125” of EL coming out of my last IPR cycle (already registered 0.125” EL from my last cycle): it’s been three weeks of since my last I-phase and 1 week since going into R-phase after a 2 week P-phase so if that additional 0.125” is going to appear, it would probably be in the next week or so…day 12 or R-phase is the magic time when I’ve most commonly seen EL gains appear.

So not going to call BPEL 9.5”…yet. But BPFSL is definitely 10.00”. Pretty amazing to be using the double digits area of the ruler.

xeno

Congrats on the milestone, you’ve been racking up the gains recently. Next summer we’ll be reading about your 10x7. :clap: