Gaining volume with Kyrpa

Water. But not open water. Either it is air It is the bulk streaming happening in vivo which is the case you are describing I suppose . Even if in the case of occurring the energy of the acoustic streaming is absorbed by the tissues as the wave continues. These are low intensity applications not high energy focalized beams used to break kidney stones of killing tumors with hyperthermia. These are not low intensity shock waves either with these frequencies and energies.

When the 1 MHz is applied in to soft tissue the amplitude attenuates quickly . At the estimated depth of the colliding waves at 2cm the 1.6w /cm^2 intensity has decreased to 0.8 w /cm^2.
In the case of perfect synchronization caused amplification the amplitude would be the original level single transducer produce at the surface. Which would mean emulating the intensity provided at the 2 cm depth applying 3-3.5 w /cm^2 at the surface with the single transducer. But because of the angle of the axis the amplification is not 100% if the synchronization occurs at same phase.

You like to flirt with the potential disaster but like you suggested already soft tissues absorbing a lot of energy, and these wave beams not being focalized ,streaming not likely to happen, are we really in the implosion range. Although these are important aspects to evaluate in the case of unknowns.
I have been very cautious with the dual setup starting with low intensity setups before graduating in to full intensity and I really don´t recommend it to anybody except me and Manko.
If he is not electrocuted already.
I don´t know but if the Einstein or even some of his students ever needed a bigger dicks I think we were all having nine inchers already.]

The insides of the US Pro 2000.
Even if I think the main brain being unmarked?.

The other side as well

So I started experimenting with girth work this week. I attached the Penimaster cap under very light tension so that my penis is fully stretched out but under minimal tension - only enough to be able to heat the full length of my penis. I then applied US heat all over in different locations for 10 minutes at 2.0W 3MHz, gently pushing blood from base to tip to get things nice and warmed up. I then removed the PM cap. I purchased the LG hanger Jelq roller. This thing is amazing quality made from machined aluminum and medical grade silicone. My grandfather from Norway was a machinist and extreme perfectionist, he would have admired this. I have been experimenting with this in different modalities, trying to get the best ballooning and them holding it for a period of time. I use it for 3 or 4 minutes at a time, them re applying US heat in between sets. This device seems to work well at getting the chambers pumped without excessive stretching of the ligament, because I want that to rest and heal for a while. Total time was about 30 minutes for the workout - I did it for 3 days, one time day one in the am, twice day 2 and 3, morning and lunch, then off today. The interesting thing, is that when I measured my resting BPFSL1 ( I haven’t been measuring BPFSL2 because I haven’t been doing longitudinal stretching), It jumped from 195 to 199. I measured yesterday in the evening when I got home, and again today in the am when I got up because I thought I made a mistake. Considering my BPFSL1 has fluctuated between 194 and 196 over the last month with no increase, todays measurements definitely have me scratching my head.

Maybe the US heat is allowing accelerated healing of the ligament fibers, maybe stretching in a different modality is having an effect. Hard to say - I’ve only done this for 1 week, but I will continue to do and see what happens.

Different story but similar results. I do the switch after the post exercise BPFSL2 has stalled but the BPFSL 1 has still been gaining 1-3 mm within 1-3 weeks. Now you are getting 4 mm and I am not so surprised but still amazed by the quantity.

For the method, tool and the grandfather heritage big plus from here. Keep going and take care not to stress lengthwise more than is unavoidable.

That voltage regulator is rated 25 degrees from factory that’s why there is a heat sink above it, I don’t see anything that’s gonna stop it in the near future, your two transistors are laddered on the side, other than the voltage regulator it’s all good

Do you see any possibility to tune this one up 25% with output intensity?
Or if I were to change the piezo ceramic transducer element to 2MHz?

Changing R12 and R13?

Increase piezoelectric transducer acoustic output with a simple circuit - EDN

You’d have to change the volts input right before the transducer and maintain the correct voltage output right after it

Thanks. I have look at it if I have the opportunity to examine it with the oscilloscope and all.
The input circuit seems to have capacitors parallel with the resistors and all not like in the simplified circuit in the example.
Some calculations are needed on impedance but I can manage it with my modest knowledge on these kind of electronics I suppose .

Hi kyrpa! Can you detail the process of heating with the transducer? My ultrasound just arrived, it is the delta-07-FND i think the same as longerstretch has but mine is 1mhz instead of 3mhz. I just tried 10min hanging over and the leg, moving the transducer slowly on just half the shaft and with 1.6W/cm2. The heat was almost non existent.

Use your hanger and hang OTL . Your penis against the skin of your leg.

Tune your machine for the 1.6 - 2.0 w/cm^2 intensity.

Use a lot of conductive gel .
Using a lot of conductive gel circulate the the transducer 5 minutes at the area of half of your penis constantly moving.
Using a lot of conductive gel circulate the the transducer 5 minutes at the area of other half of your penis constantly moving.

At this point you will be feeling the shaft is warming against the skin of your leg. Switch side and hang OTL over your other leg.
Using a lot of conductive gel repeat the procedure seen above for heating.

At the the range of 10 - 15 minutes point you can feel the heat inside your penis being constant and you are able to move the transducer along the whole shaft without losing the warmth on the area you are not operating at the moment.
Continue up to total of 20 minutes.

You can feel the skin being warm against the thigh but not necessarily anywhere else. Core of the penis heats regardless of this.

I appreciate this thread. I’ve read through the entire thread but it took me a few days to get through it since I have a busy schedule. I’m having a hard time finding any info on the Ultrasound.

Here is a breakdown of what I’m doing and using at the moment.

Machine: US Pro 2000 2nd Edition (Bought on Amazon)
Settings: I use the Medium setting (Power Output: 3.20W±20% Intensity: 0.80Wcm²±)

Routine
Straight Out hanging with a bungee cord attached to the wall using the LG Hanger chamber. The LG Chamber covers a fair amount of my shaft so only like half of the shaft skin is exposed to be in direct contact to the Ultrasound. So I’ve divided the area into 2 sections on the right/left of the shaft. I spend 5 minutes per section making fast or slow small rotations. Since I’m hanging straight out, I hold a rice sock on one side while using the Ultrasound on the other hand while pressing on my shaft like a sandwich while using the rice sock.

Concerns
- I don’t feel the heat at all even during or at the end of the 10 minutes. I do feel the tingle sensation throughout my shaft (I think) because I’m not sure if I’m losing pressure in the LG Chamber while trying to sense the tingling feeling.
- From time to time I will focus on feeling the vibration coming from the Ultrasound to see if my ultrasound is even working.
- I don’t even know if my Ultrasound is even working since again, I’m not getting the warm sensation on my shaft at the end of the session.

I look forward to reading the reply to the above concerns and any tweaks that you may suggest or anyone that is currently on this protocol.

Hello Paragdim,.

For your concerns it is obvious.You can´t get your penis heated up with 0.8w/ cm^2 intenstity. That is simply not going to happen for any of us.
You will struggle to heat it up to +40C within 10 minutes heating time with the maximum intensity 1.6 w/cm^2 of your current machine.
After 10 minutes you can feel it to be heated all the way.

I hope you will find links I provide here being informative.

These are heating tests done by me and Manko007:
Ultrasound for penile therapeutic temperatures
Ultrasound heating for penile therapeutic temperature part 2
US warmup and cooldown charts and data table

This recent post takes a look into safety limits of the heaing session:
Kyrpa - Gaining volume with Kyrpa

I am composing a thread over ultrasound use in PE.

It takes some time but I feel it necessary to separate it from the several ongoing threads new adopters asking the same questions several times a week.

Until then be patient and use the advantage search and do the learning.. Search for ultrasound , search for posts from Manko007, DocJ, Longerstretch and Kyrpa.
Once the thread is up then you need to be patient and use the search and do the learning.

The keys to follow are:

- Use more than 1.6w/ cm^2 intensity
- Use equal or less than 2.0 w/ cm^2 intensity
- Use lots of conductive gel. A lot of. Dry Skin transducer contact does not conduct the ultrasonic waves nothing more than poorly if at all.
- Keep the transducer in slow constant movement.
- Don´t expect the whole shaft to heat up completely under 10 minutes. You would still need vigorous heating to keep it up. The penis cools down really fast.